Software breakpoint warning when trying to upload program??
hi Craig,cont....from "Blackfin linker out of memory"I am getting this new error!!"Warning! A Software breakpoint is being placed at address 0x**********. This could either be an explicit...
View ArticleRe: ad7730 problems.
The device has the same problem in all its range (0g-3000kg). Greetings.
View ArticleAD8432 - Where can I get the NF vs frequency graph?
Dear SupporterRefering to the AD8432 data sheet, there is a no graph of the NF versus frequency.Can we get NF versus Frequency from 1 KHz to 10 MHz?.ThanksFreddy
View ArticleADF4351 - Band select clock mode Reg 3 and Reg 4 limited to 244?
Dear SupporterFrom the ADF4351 data sheet, reg 3 - Band Select Clock Mode - the value of the band select clock divider must be less than or equal to 254.This note is found for reg 3 but not for reg 4....
View ArticleRe: Questions about EVAL-AD2S1200CBZ
Hi JohnnyG, I'll consider to use this card you recommend instead of the CBZ.Thank you for your help. Regards,Arnaud
View ArticleRe: ADIS16480 issue
I'll run a test this afternoon to get the log. Is there a good way to determine when new data is available for the accels/gyros similar to the status bits for the mag/baro? Or should I just sample the...
View ArticleClik here to view.
Practical OpAmp filter based on Filter Wizard design not working
Hello,I have built a filter exactly to the design I created using Filter Wizard; part of the circuit ( 7 pole Chebychev low pass ) is shown below. But my filter doesn't work, there is no measurable...
View Articleusb to serial connection with Blackfin Stamp and uClinux
I want to start programming on a Blackfin BF437 Stamp board. I am having a problem with the usb serial connection. When I am connected via Kermit and I RESET the board, the uClinux OS boots and I see...
View ArticleADP5134 Enable Pin Voltage Range
HiI want to use your ADP5134 and convert 5v to 3.3v , 1.1v and 4v(using LDO).What is the voltage range for the enable pin ? in case i want to control the enable sequence.I didnt find this values in...
View ArticleRe: Reading the ADXL345
Hi. Thanks for this information. I am using adxl362 and I will do self test. My measurement range is 4g. I have few questions. 1-) Should I enter measurement mode before self-test?2-) Should I read...
View ArticleRe: Using EPPI to adress Display in Microcontroller Mode
Hi, Unfortunately the question is not clear to me. In the first line you mentioned that "We got it working now by using FS2 as Chip Select of the Display" and then you are asking if the EPPI...
View ArticleRe: When they are really available ADC data in BF506F with ACM?
Hi Maurizio, That is what my understanding is based on information given in datasheet. If you need confirmation or more details, please contact private support channel where we can ask this to analog...
View ArticleADV7611 I/O voltage levels
Video, Is it possible to run the ADV7611 on 3.3V and use 1.8V IO levels (from an FPGA)??If not, do you have some 1.8->3.3->1.8V translator chips? Or, do you have something similar to the ADV7611...
View ArticleRe: CEC with ADV7619
can you tell me about any software where check or simulate ADV7619 and ADV7511 codec based circuit?
View ArticleRe: ADV7188 - ADV212 Problems - Urgent !
And this means that the voltage range of my video signal on AIN1, as i had attached my scope snapshot, which swings between 1.3V and 2.5V (having an ac range of 1Vpp) is normal and i wont have a data...
View ArticleRe: ADV7611 I/O voltage levels
Hi Harry, The digital inputs/ouptuts are designed for 3.3V (DVDDIO). If you look at the digital input specifications Vihmin = 2V which precludes using only 1.8V input voltage levels. Any common 3.3V...
View ArticleRe: Can't load driver for AVDS-USB-ICE Emulator
Hi, It’s not clear from the title of your email if you are using an ADDS or ADZS emulator. If so then please take a look at the following FAQ which details which the minimum software versions required...
View ArticleRe: ADV212 out of buffer in docoder mode
Hi JS, This is an expected and normal problem if the VCLKs are not locked together. Even the smallest variation in clock frequency will eventually have a problem. You really only have 2 options:1)...
View ArticleAD9914/15, registers for Programmable Modulus
Hi In Programmable Modulus, where are the A and B registers? I can't find them specified anywhere in the datasheets. Best regards Quang
View Article