Re: ADE 7880 no-load conditions
Hi hmani,I configured the ADE7880 that an interrupt is generated when FNLOAD or VANLOAD in the STATUS1 register is set. Then I check the PHNOLOAD (NLPHASE[x] and VANLPHASE[x]) register for all phases....
View ArticleRe: AD7606 MISO Doesn't Work
Hi, I am checking on your schematics. I will get back to you soon. Thanks,Karen
View ArticleCF Function in ADE7763 IC
Hey hi everyone, Can anyone clear me about my this doubt that what is role of CF in ADE7763. and also help me to give me detailed information about CFNUM,CFDEN. and how it's useful in Active power...
View ArticleClik here to view.
About AD9222 evalution board and the capture board (HSC-ADC-EVALC)
(各位好，我正在使用AD9222评估板和HSC-ADC-EVLAC数据采集板，现在碰到了如下问题，希望能帮助解决。 我将两块板子如附件图1中所示连接了起来，用电脑和数据采集板连接之后，使用Visual Analog 软件无法获取到数据。)Hello Everyone, I am trying to connnect the evalution board of AD9222 to...
View ArticleADV7441A STDI_DVALID not available when some RGB timing input
1920x1200 reduce blanking Analog RGB+Sync input, Sync waveform is normal User Map, Address 0xB1-0xB5 value as below read address 0x40 offset 0xb1 len 10!...
View ArticleRe: AD9361 API Driver Implementation in Spartan 6 using MicroBlaze
Robin,Thanks for the info.I'll try changing to kintex series. will get back to you if i have further queries Regards,howtoworkwithdevices
View ArticleClik here to view.
Re: I have a problem with Video in out kit 561
Hi,I fill in the missing chroma information in here: j = 0; // Make a copy of Cb and Cr components // and retrieve the...
View ArticleRe: ADV7611: HDMI input signal is not detecting
1) Below the register settings are followed for configure the ADV7611 base, HDMI Receiver(ADV7611) Register...
View ArticleRe: AD9954 modulate issue
Hi Louijie,it exhibit more spur within the spectrum.if baseband board and DDS clock must be synchronous?
View ArticleRequest about s2p file for AD8367
Dear Sir, We are working on AD8367 chip as AGC. We would like to match to a custom frequency not enlisted in the table of the DS. Hence request you to kindly send over the s2p file for input and output...
View ArticleRe: AD9361 RX and TX ports S-Paramater
hi tlili, thank you very much for your reply..if i use wide band transformer for Rx ports what will be impact on Noise figure and IP3?since Rx ports is having different impedance at all frequencies, if...
View ArticleClik here to view.
Re: My DSP/DAC Project
Thanks for the heads up Yagami... I have 2 choices I guessKeep on current path and change some register settings and no other changes required...DSP1 OUT:To DSP2CH 0-2 TDM4CH 4- DisabledTo DSP3CH 5-7...
View ArticleRe: ADV7511W Video Troubleshooting
Digging through the various edid info I've collected from 4 TVs. Attempting to send CEA format 4 (720p). Chip reports detected VIC of 4 and sent to rx of 4. I double checked the CEA spec to ensure my...
View ArticleRe: ADE 7880 no-load conditions
Hi Heimo Thanks for sharing that info! As I said earlier, I am currently working on an alternate recommendation and I will get back to you within Wednesday ( 04/02/2014). Let me know if you need to...
View ArticleRe: what's the difference between the application for sigma studio version of...
Hi Deepac,The back channel in my project doesn't work,so I use the debug information instead.As shown below is the code and some debug information in my project. CYCLES_START(oCycleCntStats); /*...
View ArticleWhat is the BF60x max Link Port clock frequency?
Hello:What is the BF60x max Link Port clock frequency? I found two seemingly conflicting statements in the BF60x data sheet rev. A dated February 2014. According to Table 17 on page 53, max LP...
View ArticleRe: ADE7758 fires continously Interupts
Hi sommer 15 out of 75 parts is really a high percentage of failures. I am sorry that you are experiencing such issues but I will help you along the way in resolving this. Like dBC mentioned, for very...
View Article给的例子怎么有错误啊
hdmi.h 中的 #define ADMA_BASEADDR XPAR_AXI_DMA_SPDIF_BASEADDR XPAR_AXI_DMA_SPDIF_BASEADDR 没给地址
View Article