Re: So we don't need a balun for A/D IF frequencies less than 100 MHz?
You can use either a balun, transformer or amplifier for 100MHz IF or less.
View ArticleFor A/D IF Frequencies less than 100 MHz, what do you recommend for the Front...
For A/D IF Frequencies less than 100 MHz, what do you recommend for the Front End? asked by Ajit
View ArticleRe: gpio set pj0 not working on U-Boot 2012.07-rc2 on BF524
Hi Matt, yes I can have a look on the board you shipped me, but please provide me required hardware information like schematics, and describe where I can observe the port J and other ports on the...
View ArticleRe: API/SDK for AD5667REBZ
Hi Meir, Just to clarify, the main purpose of the source code is to show how a certain microcontroller could control the AD5667R via I2C communication. The code can be your basis on creating your own...
View ArticleRe: ADCMP580 input capacitance
Hello Anna, Thank you for your confirmation. Regards,Ricky
View ArticleRe: About ADP170/1 thermal consideration
Hi glenn, Thanks for your reply.You mean that vias between top and both side and patterns are not so affected for esimated θja in the eval board? Best regards,Tarzan
View ArticleRe: Sync Multiple AD9913
Thanks Louijie - I see that Auto Clear Phase Register on the data sheet, that makes sense. I'll give it a go. Thanks again, SCH
View ArticleRe: AD9520-0 heating up and output frequency gradually decreases.
Hi Paul,Sorry i am using PLL(Writing 0x7C to 0x010). The LD pin is staying low.I have observed the oscillator is stable giving around 24567320Hz. Looks like the PLL is not able to lock. What are the...
View ArticleAD9361 API Driver Implementation in Spartan 6 using MicroBlaze
Hi, Am using AD9361 in my project. I've been trying to initialize the chip by configuring all the parameters. I happened to go through the code available online for the ML605 evaluation board. I wish...
View ArticleRe: cn-0209
Hi, As in your previous reply, if I interface AD7193 ADC with ADSP-CM40XX,then what about the on chip ADC of the processor? Regards,Divya
View ArticleRe: Problem with AD9361 transmission
Hi Yossi-S, Am using AD9361 too. Am experiencing the same problem. For whatever i transmit, i'm getting a low output power of -60db. How did you correct this issue? Besides, i tried operating the...
View ArticleRe: AD9361 API drivers for Microblaze
Dragos, Actually, we are using only CMOS mode. The drivers are given for LVDS mode. How should i convert the existing drivers in LVDS mode to CMOS mode? The AD9361 IP is linked with DMAC in Xilinx XPS....
View ArticleRe: interrupt nesting and poriority
Hi, The Priority order for 3 interrupts : IRQ > DAIH > DAILDAIH and DAIL both cannot have the same priority level Regards,Mahesh
View ArticleRe: AD9361_Frequency band of operation
Thanks tlili If i add one mixer stage or any multiplier will it be any complexity?or please suggest any solution? Raveendra
View ArticleRe: SNMP on bf 537 stamp
Hi Deep, which software version are you using or do you intend to use? generally we would recommend you to use the latest buildroot, follow this to build a typical target...
View ArticleAIN and ADC assignment for video input of ADV7181D.
Hello. I have questions about AIN and ADC assignment for video input of ADV7181D.The customer is going to use ADV7181D with four CVBS inputs and one s-video(Y/C).I'm suggesting the assignments as...
View ArticleRe: AD8215
Hello Emmanuel, Thanks for your info. Waiting u to reply for the rest of questions. Rgs,Chai
View ArticleRe: how to rebuild the project(AD-FMCOMMS 1EBZ) using SDK?
Dear DragosB, We purchased FMCOMMS-2EBZ board. We are planning to configure the FPGA from CompactFlash. Could you please tell , what are the files we need to store in Compactflash ? how the structure...
View ArticleRe: AD7705 with 4.9152M Crystal does not work well
Hi schichen717, I noticed that vias are used for the MCLK connections which also add up to the total load capacitance. As mentioned, this will make the lines imbalance. So, it is best to make these...
View Article