Re: How could I use sigmastudio for 21375?
May I just change the processor setting in the "Properties" dialog box to resolve this problem by rebuilding another new project?
View ArticleAbout ZedBoard's ADV7511 reference Designs
With the reference Design, there is a IP core that ADI provides .(axi_hdmi_tx_16b_v1_00_a).Here is the question, How can i change the dataformt of output ,while the 16bits Ycbcr4:2:2 is set to be...
View ArticleRe: Fiber Optic Gyroscopes
Based on the key ADC specifications you have offered, it would appear like the AD7760 is the closest solution I can point you towards: www.analog.com/AD7760 I hope that helps. Best,NevadaMark
View ArticleRe: EVAL - ADAU1452MINIZ
Hi Philip, Sorry you're experiencing this trouble. The good news is it looks like we can clear it up quickly. I switched my board's self-boot switch to enable and duplicated your...
View ArticleRe: EVAL - ADAU1452MINIZ
Hi Bob, I have a small addition/correction to make to your post. You can actually control the ADAU1452 from SigmaStudio after the self-boot procedure is complete, given that a few conditions are met....
View ArticleClik here to view.
Re: ADAU1450 and 1451?
Hi Miguel, Small correction to your post. Full speed is 294.912 MHz. Half speed would be 147.456 MHz. Yagami
View ArticleRe: ADAU1401 crystal oscillation
Hi Bob, Cool ideas! I have some additional information that might prove helpful when using this approach. In both cases (overclocking or underclocking), a good way to change the frequency-dependent...
View ArticleRe: Using the AD193x Component in Sigma Studio
Hi Dave T, I have a small addition/correction to make to one of your earlier posts. The ADAU144x executes its self-boot function using the I2C port. So, it is indeed true that the ADAU144x needs to be...
View ArticleRe: AD9249 Internal Vref Histogram
Can information on this case be disclosed? Thank you.
View ArticleRe: My DSP/DAC Project
OK, well now this is getting more interesting! Let me try to break down the problem here. I find it easier to collect my thoughts by writing them down... DSP1 has two input clock domains - DIX9211 and...
View ArticleRe: My DSP/DAC Project
Whoops, I just saw your updated post. I agree, keeping it simple is best. Having each DSP be independent and not crossing data lines keeps a lot of complexity out of the design. As far as addressing...
View ArticleRe: Interfacing Microcontroller with AD9959
Can you send your setup (.stp) file? You can save your setting in the eval board GUI and you may attach it here. I will evaluate here in the lab using the settings you have.
View ArticleReflected into the load, or reflected FROM the load?
Reflected into the load, or reflected FROM the load? asked by Ajit
View ArticleRe: Reflected into the load, or reflected FROM the load?
Not sure in what context you are asking this question. I assume you mean the return loss. If so, then the impedance is reflected from the secondary loading to the primary loading.
View ArticleRe: Does Analog Devices recommend which baluns vendor and which balun...
We recommend the following baluns which we use on most of our eval brds. These give us very good performance in order to hit the dynamic range of our converters. ADT1-1WT, ETC1-1-13M,...
View ArticleRe: 1-D DCTs
Yes, the input is always real, and I agree it is a DFT of even real function. In this case I am required to use DCT-II as shown in the Wikipedia article on DCT....
View ArticleDoes Analog Devices recommend which baluns vendor and which balun...
Does Analog Devices recommend which baluns vendor and which balun configuration is best used with the A/D converters? asked by Ajit
View ArticleRe: ADCMP580 input capacitance
Hi, ricky. Thank you for using ADI products. Unfortunately, we do not have the information you need but according to the Applications Engineer of ADCMP580, Vp and Vn input pins have high impedance and...
View ArticleSo we don't need a balun for A/D IF frequencies less than 100 MHz?
So we don't need a balun for A/D IF frequencies less than 100 MHz? asked by Ajit
View Article