microcontroller or processor with atleast two UART and two CAN interfaces
Hi, I am doing a project of developing an Universal Analog Input Module(with 4 channels).I am thinking of using your CN-0209 as the reference circuit and modify the circuit for 4 channels.But I am...
View ArticleRe: [ADV7181D] Output screen size at free run mode just after power-up...
Hi Dave,Thank you for your reply. There are descriptions about free-run mode on datasheet as follows:Page 6."Free run output mode providing stable timing when no video input is present" Page 193."9.5...
View ArticleClik here to view.
Re: RS-485 full duplex problem
Hi Richard, Thank you very much for your help! The problem was in R33 resistor - there was no resistor on my PCB! Thank you once again! Best wishes, Viacheslav
View ArticleRe: problem with ldf of 21375
Hi CraigG,As you said,it will just increase by the size of the data type of the pointer rather than the size of the bus,but what will the bus effect?And what is the different between the different...
View ArticleRe: cn-0209
Hi, As I mentioned in my previous post,I require a microcontroller with atleast two UART and two CAN .So if I use the ADuCM361,the is it possible to add the required UART and CAN to the processor?...
View Articleinquiry on ADV212
Hello,DaveD, Thank you for your response! In my application, (1)the pixel clock is under 75MHz (2)Though the tile size is more than 1.048 million,there is only...
View ArticleSimple AD8232 Eval Board question
I have the AD8232 Evaluation Board, with additional identifier on the board as A03321 REV A-7. I need to determine the type of female connector used for the various terminal points used throughout the...
View Articlehdmi to composite and composite to hdmi circuit and file
i need making converter from to hdmi to composite and composite to hdmi circuit and file what ics i used and need circuit thanks
View ArticleRe: Connection check and filter question AD9834
Hi,Your values are okay given your output freq is up to 2MHz only.Without filter, the 1st image has the most power level next to fundamental. So, you are good to go with your filter. However, I suggest...
View ArticleRe: Simple AD8232 Eval Board question
Hi William, Just to confirm, is the board you're working with the same as the one in the link below?http://wiki.analog.com/resources/eval/ad8232-evaluation-guide/a03321a Thanks, Kris
View ArticleRe: adas code
Hi, Please advise what ADAS product it is that you are developing your application around on. Regards,Karen
View ArticleAD8347 Eval board
Hey I am using AD8347 for my project. I want to know does evaluation board contains only the demodulator or does it provide the ADC Low noise amplifier to test the IC capability entirely? I couldn't...
View ArticleRe: ADV7513 Differential output appears single ended
So we have new information on the problem. 1) The cable we are using appears to have a low ohm to ground short (40 ohms) on the non-inverted HDMI signals. We went out and purchased two additional...
View Articlea finished prototype
Hello guyz! It is not a question, I just wanted to "boast" a little bit about the prototype of the ultrasonic device for the blind. It uses two boards, the top one is an adau1701 based computer (can I...
View ArticleAD9257 power consumption question
Hi all, I'm looking at using the AD9257-40 in a new design, but this is a battery-powered application, and power consumption is very important. I have 12-channels that I need to sample, and so I'm...
View ArticleEVAL - ADAU1452MINIZ
I watch the video to configure filters. I used CH0 for stereo input. GPIO as output. I downloaded the program. When I move the slider bars for amount of increase or decrease amplitude. The program...
View ArticleClik here to view.
Re: EVAL - ADAU1452MINIZ
Hi Philip, GPIO outputs refer to digital output pins used to control external LEDs and such. The audio DAC outputs are called simply outputs, as shown below: The most frequent cause for...
View ArticleRe: ADV611 problem
Hi Dave, As you say this kind of situation, will suggest we ADV611 change into ADV212 or other chips, so other chips will provide evaluation board and the information?We mainly is the use of FPGA to...
View ArticleRe: Help regarding AD9858 Schematic.
Have changed 0x12 to 0x82 but no positive change has been seen. The DDS just lock the start frequency i.e 110MHz.
View ArticleHow could I use sigmastudio for 21375?
I would like to use 21375 with sigmastudio,but after I have allocated all the 10 memory blocks of sigmastudio in 21375 and I am going to do some initialization jobs for sigma in 21375.The errors just...
View Article