ADV8005 pinkish color issue
in the datesheet, it shows that ADV8005, using HDMI input with 4Kx 2K video format & RGB color space, output video is in pinkish color。 it is software or hardware problem? How we can solve it?
View ArticleRe: Transimpedance(I-V) converter opamp suggestion
Hi Lefteris, Sorry for the late reply. Your thread got buried in the forum. I will look into your questions a bit more, but for the time being, is the ultimate goal of your study to measure the...
View ArticleClik here to view.
AD9361 SFDR & SNR problem
Hi, I am working on AD9361 in my customized board and i am facing some problems on receiver side. Below i mentioned few questions on AD9361 1. I Configured the chip with below settings. FDD mode, RX...
View ArticleClik here to view.
Re: Be confused by Physical Address and Logical Address on HDMI CEC
winkle.zr.zhang@gmail.com撰写: Hi PoornimaThanks for you kindly reply.as you said, Give standby message from 78842 to Home-Theater, Home-Theater goes to standby mode.80 00 0F, 80 01 36,The next step, I...
View ArticleRe: Be confused by Physical Address and Logical Address on HDMI CEC
Hi PoornimaNow i use to ADV7842 Evaluation platform and TestData as below. 1. EDID set register 9E:10 9F:00(Phyical address)2. write rigster:wri2c 80 4c 00wri2c 80 2a 3fwri2c 80 27 10wri2c 80 28...
View ArticleRe: AD5932
Hi Miguel, Yes, I have enabled the pin in the control register as per the datasheet i.e. D2 and D3. But still it is not working.Also, I am trying to give the output of AD5932 as an input to an opamp....
View ArticleRe: Preamplifier (impedance matching) for EVAL-AD7357EDZ
Hi Dimitrios, Yes, you can use the EVAL-PRAOPAMP for these amplifiers. Just make sure that you purchase the correct eval board depending on the part's package and no of channels. Also, I noticed that...
View ArticleClik here to view.
Re: ADAU1701 have level data feedback to MCU?
Alhamdulillah, I manage to work with SPI control. But... I wonder why the signal at the MISO line is not stable. Unacceptable Inconsistent data output from ADAU1701 and sometimes, when there is a data...
View ArticleRe: OP4177 Power Voltage Supply
Harry, thanks for your input. Any idea why Analog use this way of specifying the power supply voltage?
View ArticleClik here to view.
ADV7393- Sync on Green
Hi, I have to confirm the ADV7393 sync on RGB output.I need the sync signal on output green line, so if i enable the Sync on RGB bit to high, shall i get the sync signal only on green DAC output line...
View ArticleRe: AD5932
Hi Shalini, May you share the schematic? The output pin problem is quite unusual. May I recommend to double check ALL pin connections, and verify using an scope that the digital transmission is done...
View ArticleClik here to view.
Re: Setting up the communication between zedboard and pc via ethernet cable.
Hello Di, The problem is I think with the connection between zedboard and my PC. Even when I put both of them in the same network it won't work. I tried even the example for matlab filter design as in...
View ArticleRe: input cap. ADA4800 ?
Hi Adri, I'll get back to you on this once I get a response from the applications engineer of this part. Regards,Jay
View ArticleClik here to view.
Re: Re: ADV7625 OSD Text characters are not clear during emulation and...
Hi all I use Blimp3.7Exp8 to test my project,when emulate the result is OK,but when down load into machine,some string display un-normal,don't display in MiddleCenter even if the TextAlign had been...
View ArticleRe: Aduc7122 Operation Temperature?
Possible alternative would be the newer ADuCM320 fully specified for -40°C to 85°C!?If you want/need to stay with the ADuC7122, the question is how long and how often you need to go to -40°C.The...
View ArticleRe: ADuCM350 evaluation board questions
Hi Richard, Good to hear you are making progress with your evaluation of the ADuCM350!It definitely sounds like you have outgrown the EKSP! This software was designed to enable quick and easy impedance...
View ArticleMIL-STD-833B documents
Dear Sir. ADI has many MIL-STD 833B compliant devices.I would like to see the MIL-STD-833B documents, that is ADI supported.but I can't find in adi site. How to get that?We can get MIL-STD-833J, but...
View ArticleRe: MAT14 vs. MAT04
Hi AnnaFeB, Could you suggest me when I can receiver your answer?My customer asked it to our sales person. Best Regards,Ricky
View ArticleRe: AD9631 for custom design with zynq - xilinx
Hi Adrain, Thanks replying for my request, Actually we are using AD9634 in our board with zynq as BBP, somewhere i read in AD website that only difference in AD9634 and AD9631 is the number of channels...
View ArticleRe: MAT14 vs. MAT04
Hi, Ricky. Sorry for this delay. I have not received any feedback yet. I'll update you once I received it. Regards,Anna
View Article