Re: ADV8003 eval board running hot
Could you show us the setup. It is the quickest way to resolve the issue when we have the same setup. So we could repeat and debug the issue.
View ArticleAD5370 Eval - Software Development API - CYPRESS USB (EZUSB CYUSB)
I would like to be able to write my own software to interface to a EVAL-AD5370 DAC board. Does anyone know if Analog Devices has a published software document that describes how to interface to their...
View ArticleRe: Running AD9516_17_18 Eval SW on Win7 64 bit
Hi A got sort of the same problem but with the ez-kit lite bf533. I can find a usb driver for win 7(64 bit). Is there also a fix to this problem? ThankDalle
View ArticleRe: ADP1047 Evaluation GUI Installation
If you are using Windows Vista or higher, you can ignore the error. The GUI will work perfectly.If you are using a version of Windows which is older than Windows Vista, then click on the link it...
View ArticleUnused pins of ADV7619 port
What should be done with the unused HDMI pins on one of the inputs of the ADV7619 if you are only using one port?
View ArticleClik here to view.
Re: Sigma300 (ADAU145x) Q&A
As I see, it does not require any modification on the board itself.2 headers (f+m) and 2 resistors should be enough soldered together or on a small breadboard.I would tend to think, that this should...
View ArticleRe: HDCP Handling of ADV7511W.
Setting HDCP frame enable bit before HDCP desired bit by itself may not solve an Ri mismatch issue. HDCP Ri mismatch error typically caused by HDCP not disabled in proper sequence with stopping...
View ArticleRe: Sigma300 (ADAU145x) Q&A
J1 facing downwards, J2 upwards, J0 connected to TP1 (A_3V3)
View ArticleRe: AD-FMCJESDADC1-EBZ reference design not working with ZC706?
I programmed the FPGA with the cf_fmc176_zc706.bit file using iMPACT. However, no characters are displaying on the UART terminal. Also, Chipscope finds 3 ILA cores, but when I trigger each of them on...
View ArticleADIS16485 - data ready indicator does not fit output rate
Hello there I've had the pleasure to work with an ADIS16485 IMU lately but currently have some trouble setting the little fellow up to the application specific needs. I'd like to run the IMU at way...
View ArticleRe: Frequency Modulation with AD9910
After every loading operation listed I am issuing an io_update.
View ArticleRe: Reg ADSP-CM403 ADC
Hi Vijay, 1. You are correct. When you use Flash based configuration, the IAR downloads the code in internal SPI Flash memory of processor and applies a reset. So, while debugging, you can use SRAM...
View ArticleHow to get accurate readings in ADE7763's Vrms register
Hello everyone, as I am using ADE7763 to measure the Vrms,Irms and Active power.but when i am reading the Vrms register as the method suggested in the datasheet of ADE7763, i did...
View ArticleRe: CLK Multiplier on ADI
Hi Meir,Can you please elaborate on their requirements:How is the reference frequency generated and what logic type is this signal?Do they need multiple outputs? What output logic type does the...
View ArticleRe: ADE7880 Neutral - Ground Question
Hi Dave, Yes I was referring to the AGND and DGND which is connected to the host microcontroller GND. Due to this, the entire board was spoilt when I mistakenly connected the phase to the neutral. So I...
View ArticleAD9910 - Simultaneous use of RAM and DRG- Is it applicable?
HiWe are using AD9910 and we have technical question and need your advice.We are configuring the AD9910 to operate from RAM for frequencies. We are using the whole 1024 frequencies in RAM.We want to...
View Articlecan4linux and serial RS232 incompatibility
Hello, I got a problem when I try to use both a can communication (Can4linux driver) and a serial RS232 on port com ttyS0 : - If I use each one independantly in a compiled program, everything works...
View ArticleRe: ADuCM360 ADC
What is your input voltage?Have you biased up above 100mV - see input specifications!Also have a look into the following threadhttp://ez.analog.com/message/115302#115302
View ArticleRe: Help!!! My AD7192 is working way to well, without an input buffer...
Shannon, The spec table guarantees that in unbuffered mode, the input current is higher, but you can get within50 mV of the rail. In buffered mode, the input current is lower, but you can only get...
View ArticleADuC7061 Source code for CN0196
Hello! I have the evaluation boards for the circuit from the lab #196 (http://www.analog.com/en/circuits-from-the-lab/CN0196/vc.html) and i was hoping to make some modifications to the source code...
View Article