Re: Choosing the right ADC for the job
The zero Ohm resistor can be eliminated and a simple trace be used in the final application. Zero Ohm resistors may be used for a number of reasons. In the case of evaluation boards, they are often...
View ArticleReference gravity in m/s² for ADIS16485 ?
Hello again According to the datasheet acceleration measurements on the 16485 device are also integrated to a delta velocity in m/s.How does this work? I know there is a formula in the datasheet, but...
View ArticleRe: ADV7842 connected to ADV8003, Test4, Test5, Test8 Pin Conflicts
N4 TEST4 - GroundP3 TEST5 - FloatN6 TEST6 - FloatP5 TEST7 - Float, it's an output pinC11 TEST8 - tie to ground with 4.7k, really an active high power down pin we never use. UG-214 needs to be updated...
View ArticleRe: ADV7842 IOAMP IO_REG_05
Those are undocumented bits and should be left at their default values.
View ArticleClik here to view.
Re: AD9467 Display output on console
Hi Istvan,Thanks a lot its working now and i have verified the points on console in Matlab. Now i can use these samples for the FIR filters. Do analog device have any example of implementation of FIR...
View ArticleRe: Reference gravity in m/s² for ADIS16485 ?
Hi Vinci! Thank you for posting this question. You can find that information in this FAQ post:http://ez.analog.com/docs/DOC-2755I hope that this helps! Very best,NevadaMark
View ArticleRe: ADIS 16405 Output Problems Using Raspberry Pi
Just wanted to check back in on this. Were you able to verify that the connections, voltages and SPI signals were all correct? I know that this worked before, but sometimes things can be accidentally...
View ArticleRe: CLK Multiplier on ADI
Hi Meir, We have the AD9553 digital PLL which is a three input, two output device.http://www.analog.com/en/clock-and-timing/clock-generation-and-distribution/ad9553/products/product.html An analog PLL...
View ArticleRe: Advantiv® Software architecture specifications document
Hi Hank, I'll check. I thought it was posted somewhere. Dave
View ArticleRe: BF561: Crash during initialization of C-runtime
I'm still struggling with this problem. I have identified a way to recreate it as simply as possible: Create a new project for the BF561. Do not enable startup code/LDF generation. Select "Add source...
View ArticleADIS16445/ADIS16448 Application Note for Mechanical Design
Check out this application note, which summarizes the best mechanical design practices when developing an installation approach for the ADIS16445 or ADIS16448 IMUs....
View ArticleRe: ADXL375/ADXL377 Data Communications Ideas
I agree with Mark. Theoretically, you can wirelessly stream the data to a handheld device (iPhone etc) but we don't offer any wireless solution for this product. regards,Venkat
View ArticleAutomatic Level Control in SSM2603
I wanted see if anyone could give me a brief explanation of the parameters Max Gain and ALC target level for ALC in the SSM2603 Codec. I wanted to find out how they interact and work with each other....
View ArticleRe: ADXL375/ADXL377 Data Communications Ideas
Venkat, understood. Thinking about it, it might be helpful and useful for me to test both methods (wireless and local area connection). With the local area connection I am going to look into using the...
View ArticleRe: ADXL375/ADXL377 Data Communications Ideas
What type of instrumentation would you suggest to use with the ADXL377. For example, the football helmet manufacturer, Ridell, is incorporating impact monitoring and reporting technology inside their...
View ArticleRe: Calibrating AD5933 with Arduino
Yaaaay! Thanks soooo much! That was it! I had to mask D11-D10 each time I sent a command to the control register so as to avoid tampering with the already set PGA and output voltage settings. Whew,...
View ArticleRe: AD9910 - Simultaneous use of RAM and DRG- Is it applicable?
Hi Freddy, Louijie is correct. The AD9910 DRG and RAM use the same registers inside the part so only one can be functioning at a given time. However, the AD9910 has a second ramp generator exclusive...
View ArticleRe: AD9910 - Simultaneous use of RAM and DRG- Is it applicable?
Hi Freddy, Some ADI colleagues pointed out that I made a mistake. I was thinking of the Single Tone Profiles instead of the DRG, and those cannot be used in conjunction with the RAM because they use...
View ArticleClik here to view.
Re: EVAL-ADIS C/C++ Driver or Source Code Libraries
Hello Pierre-Yves,I have attached a new DLL to this message, which makes the functions "COM visible," for C++ development environments. Our software engineer was able to do some very limited testing...
View Article