Re: What is a baud rate of AD5700-1 to communicate with micro-controller
Hi there, The AD5700-1 operates at a baud rate of 1200. Rgds,Tracey...
View ArticleRe: ADV7625 CSC in front of output
Hi Daisu, The ADV7625 and ADV7626 are very similar from a register map perspective. The I2C addresses, functions and most of the values are the same. Certain register values e.g. any controls for port...
View ArticleRe: ADE7878 Current Transformer Question
Hi Guilherme_Adao, Look for the rated phase error of CT's in data sheets, many CT's should not have a phase shift greater than the max phase delay possible on our part. For example, a CT such as the...
View ArticleADF4158 and ADF4159 software source code
The source codes for the ADF4158 and ADF4159 evaluation board control software is attached below. Warning: You use this at your own risk and it is not officially supported by Analog Devices. The code...
View ArticleRe: Question about ADV7612 connect with DM368?
Hi, First of all this is an old thread, Could you start a new one and link back to this one. It easier to track that way. For the image, the ADV7612 is basically a serial to parallel converter. The...
View ArticleRe: AD9467FMC connectivity with Zedboard
What is the frequency of the noise you are seeing? Can you measure it and tell me? Thanks Charly
View ArticleRe: ADV7393 outputs protection
The ADV7393 has a DAC output designed for 37.5 or 300 Ohm loads. Any ESD protection as long as it meets the voltage limits should work. You just have to make sure the protection does not effect the...
View ArticleSeeking Signal Definition/User Guide for the AD-FMCJESDADC1-EBZ
Hello,I'm interested in using the dual-AD9250 evaluation board, the AD-FMCJESDADC1-EBZ. I want to interface it to a custom design of mine and have not been able to locate any information on the...
View ArticleRe: Seeking Signal Definition/User Guide for the AD-FMCJESDADC1-EBZ
The FMC_TO_CPLD lines are going from the FPGA to the CPLD at Vadj voltage. Inside the CPLD we are doign the SPI logic which controls the rest of the board at a known voltage (1.8 or 3.3,...) to be able...
View ArticleRe: DAC to ADC loopback from a new IPCore
What do you mean by this?? may I know the port name between DDS and DAC LVDS interface? Literally - that will be dac_data_[i/q][0/1/2/3]. If you are familiar with HDL, you should be able to find your...
View ArticleRe: Please Help，Dose ADV7401/ADV7403 support four CVBS synchronous acquisition？
Hello, Sorry this one seems to have slipped by. The answer is no though none of our video decoders support more than a single active video channel. Dave
View ArticleAD-FMCOMMS1-EBZ relayout issue:PIC firmware programming to a micro-controller...
Dear EngineerZone:I want to re-layout the ADI-fmcomms1-ebz board.how to a PIC firmware download to micro-controller(PIC18F24J50-I/ML) on board.i use ML605 and no-OS driver.Thanks.
View ArticleRe: ADV7612 I2C not working
Hi Ben, It should be held low with a pulldown and then driven high-- however I doubt it would cause such a hard failure if anything. Not getting any ACK at all is usually one of: 1) ground pad isn't...
View ArticleRe: Some questions of ADV7619, again
Hello Kaos, Q1) Correct.Q2) No, the ADV7611 cannot. Assuming you mean ADV7619-- I think that would work but it's not something we've ever tried.Q3) Yes, I believe that is what you would see. Dave
View ArticleRe: ADIS16485 and ADIS16375- SPI issue?
Hello Freddy, In previous cases, which offer similar observations, the system supplies were not able to manage the elevated peak current demand in the ADIS16375 (1.5A, ~200us) during the start-up...
View ArticleRe: Problems using the BF527 Button_LED_GPIO example
Hi Ram, Can you please clarify what you mean by, "whenever I set default jumper setting the LED 5 off state". Does LED 5 ever go out, or does it remain on regardless of the switch and jumper settings?...
View ArticleRe: H.264 codec in blackfin??
Hi Sunil, These questions below in the Blackfin forum. I'll move it there. Dave
View ArticleRe: Rx sense problem
Hi Jun, I'll check with experts on that part with with our HDMI TXs-- it's generally HPD that triggers the transmitter system to do wake up. Dave
View Article