Quantcast
Channel: EngineerZone: Message List
Browsing all 36216 articles
Browse latest View live

Re: gpio-addr-flash: probe of gpio-addr-flash.0 failed with error -22

Could you start a new help thread for this CPLB miss issue, and close the previous PIN confiliction issue if it is resolve? let's keep the style of one thread one topic, this would make my issue...

View Article


Re: AD 215 isolated power supply

Hi C.L,  Just a few questions on your setup to help me understand the problem. You mentioned that you are using the part in a unity gain configuration. When you see the supply dropping to +/-5V, are...

View Article


Re: A question about AD9915's OSK function

Hi Sercan, In order to control the amplitude of the signal, "OSK enable" should be set in the evaluation software. If this is not set, any value in the ASF registers would be ignored. "External OSK...

View Article

Re: About interface read module for ADAU1452

Thank you very much , Miguel-san

View Article

Re: About interface read module for ADAU1452

Thank you very much ,Brett-san.We use read back module.

View Article


Re: Cell Phone detector RF component.

Thank you very much Enash, I found your suggestions really helpful and quite inspiring. I would take a look at the ADL5500  as advised, but I would also like to ask how I can make a detector circuit...

View Article

Re: What's the difference between synchronous burst mode and asynchronous...

Hi, Jobo23, I have read the relevant document. I think the code below is for asynchronous read.Would you please send me some code example for synchronous burst read? ERROR_CODE ReadFlash( unsigned long...

View Article

ADAS1000 CRC

Hello, all. I have one question about ADAS1000.Does CRC calculation include Header or exclude Header?  Thanks.

View Article


Re: About SRC in ADAU1442

Dear Brett-san, Thank you for your supports. About SRC lock time and sampling rate changing time,     Could you provide formula of them,please?     Or, Could you provide max time of them,please? Best...

View Article


Re: About voltage of external regulator at ADAU1452W

Dear Brett-san,Thank you very much for your supports.Best regards,Takepiro

View Article

Re: Closing out the Idde.exe process through the API

Hi David, From the information you've provided I cant see any obvious problems with what you are doing to close the idde. What happens after issuing the "idde.Quit" command if you leave it a while,...

View Article

Re: Failing to get CPU status

Hi John, I had noticed it too.. I have to try again after replacing the regulator in the board. ThanksDeepak

View Article

Re: ad9467 device driver

Hi, Please take a look here: https://github.com/analogdevicesinc/linux/blob/xcomm_zynq/arch/arm/boot/dts/zynq-zc706-adv7511-ad9683-ebz.dts Your SPI master needs a AD9467 slave node.This node also needs...

View Article


Re: Circular Buffer problem in SIMD mode

Hi Jithul, Thanks for the reply. We need to step through the assembly code and look at the register at each iteration in the loop. The problem is when we start with odd offset and when the index...

View Article

Image may be NSFW.
Clik here to view.

ADF4158, ADF4159 software

ADF4158 and ADF4159 software attached. Compatible with Windows XP, Vista, 7 (32-bit and 64-bit). Main Controls: Ramping and shift-keying controls: Post any problems/questions below.v410.1: Improved...

View Article


Re: ADF4158, ADF4159 software

You need to use the Ramp Complete to Muxout control in Register 4. There is now a warning icon when Muxout is set to Ramp Status but Ramp Complete is not enabled.

View Article

Re: ADFMCOMMS-1 ZedBoard Reference Design DMA Configuration

Hi Onur, Can you please take a look over the latest software from the GitHub (https://github.com/analogdevicesinc/no-OS/blob/master/fmcomms1/Common/test.c#L378)? It appears that you are using an older...

View Article


Re: FMCOMMS1 AD9643 Test Mode

Hi Mel, I will take a look over your problem and I will let you know the result. Thanks,Dragos

View Article

Re: AD5933 source code for AVR problem

I m assume plots are gathered with Rcal = Runkn = 10kMay you repeat plots with Rcal = 10k and Runk = 15k?  regards,Miguel

View Article

Re: AD5933 source code for AVR problem

No, this is measured with Runk = 15 k, Rcal = 10k. Question is, why I have on Vout pin less than 2 Vp-p?

View Article
Browsing all 36216 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>