Quantcast
Channel: EngineerZone: Message List
Browsing all 36216 articles
Browse latest View live

Re: FMCOMMS2 and Zedboard

I was first unable to import with either 14.4 or 14.7 when I created a project with Zynq/xc7z020/cg484/-1. I then created a dummy project with Virtex 7, so that I could import and open the IP to see...

View Article


Re: About interface read module for ADAU1452

Hi Takepiro, You can use the DSP Readback cell in SigmaStudio to read the signal at any point in the signal flow.http://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/basicdsp/dspreadback...

View Article


Re: AD8295 Single-Supply

MMaria,   Do you mean fig 67 on the AD8295 data sheet? You may want to play around with ADIdiffAmpCalc:  http://www.analog.com/en/amplifier-linear-tools/adi-diff-amp-calc/topic.html Also:...

View Article

FMCOMMS1 AD9643 Test Mode

Good afternoon, I am using the zc702 eval board and the FMCOMMS1.  I am trying to set the test mode of the ADC, AD9643.  I am using the XCOMM_SetAdcTestMode function.  I have been able to set each Test...

View Article

Re: FMCOMMS2 and Zedboard

Rejeesh, One more question: There are two options to regenerate IP. One says "Regenerate all project IP (under current project settings)" and "Upgrade and regenerate all project IP (latest versions,...

View Article


Re: EVAL-AD5360/61/62/63EBZ USB Software

I was able to fix all problems and get a .NET dll (AD5360.dll) that can be used to set the DAC registers and outputs.

View Article

Re: VBI and CGMS of ADV7392.

Hi Tamu, I'll get an expert to come comment. Dave

View Article

Mismatch problem for AD5242

Hi, I want to use your product AD5242 (1M). I ordered the samples and do a measurement on breadboard using a multimeter. I measure RAB for both ch1 and ch2. One is 0.8M and the other is 1M. When I...

View Article


Filter with external level, center frequency, and Q controls (GPIO)

I am looking to create a filter (General 2nd Order for now) where I can edit the level, center frequency, and Q of the filter using external controls.  So far, I have found ways to adjust either the...

View Article


Image may be NSFW.
Clik here to view.

AD817 Reduced Output

Im using a op amp as the front end for my data acquisition cardChoose the AD817 amp powered with a 12v single power supplyI have a 4v peak to peak signal going into my systemThe signal im getting on...

View Article

Image may be NSFW.
Clik here to view.

Re: is DRG Freq. Jump function works WHEN no-Dwell high&low bits are both set?

THx for your reply..

View Article

Re: AD 215 isolated power supply

Hi C.L, I am looking into this. I will get back to you soon.  Thanks!Kris

View Article

Re: Problem with AD536AK rms to DC converter

Hi Balint,  Just wanted to check up on you with this. If you have doubts about the battery, you could try measuring at the actual power pins of the part just to see if the supply is dropping or if...

View Article


Re: gpio-addr-flash: probe of gpio-addr-flash.0 failed with error -22

Aaronwu, Thank you for looking at this.I am making progress The biggest issue was in:static struct platform_device ezbrd_flash_device = { .num_resources = 1, should have been  .num_resources =...

View Article

Re: ADV7513 configuration problem

In general practice, it is never good to leave input pins floating unless they have internal pulls.  Is it an absolute requirement, no, it is best practice and recommended.

View Article


Re: Gyroscopes

Hi Jim. The In-Run Bias Stability specification represents the bias accuracy you can achieve under stable inertial and environmental conditions. This specification is derived from the minimum point on...

View Article

Re: ADIS16136 weird behaviour

So far, I have not been able to duplicate this behavior but I have asked a colleague to take some data on another unit (while I work on another inquiry). Once this data is ready, I will analyze it and...

View Article


Re: getting consistent output from ADIS 16375

How are things going?  We have had to delay our FAQ on a linear regulator design for the ADIS16375, but I wanted to offer some starting points, in case you are going to do this yourself:ADP3339 or...

View Article

Re: Can I design a variable frequency filter for a Wah Wah effect?

Thank you so much Bob! I tried it out and it sounds pretty good with a guitar! I appreciate your help and will build around your design.

View Article

problem with my ADIS16448 data output

hiim having a problem with my ADIS16448. some of the data im receiving doesn't make any sense.the pressure is 40 mbar, which should be around 1020 mbar. and the tempreture is much more higher.i sent...

View Article
Browsing all 36216 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>