Looking for Non-Rohs Comparator
I have a customer looking for Non-Rohs Comparator. Critical specs are single supply, higher voltage range and -55 to 125 temp. They are looking at TI part# TL331-EP. I was thinking ADI op amps might...
View ArticleRe: AD9914: profile mode vs single-tone vs parallel port modulation
sittie aisha magayo-ong wrote: Hi,After the basic steps, have you then tried changing:F[3:0]=0100define POW and AMP accordingly to the 32-bit parallel port.IOUPDATE = 3.3V and see if that changes the...
View ArticleRe: Transformer or Common-mode choke for Ext Ref Input?
Hi Paul, Thanks for your reply. The signal is actually being output to a BNC - would a different buffer chip be more appropriate? How should I do the output matching using the center tapped balun: -...
View ArticleRe: Swicht for input ADC
Hello Ronald, When selecting a switch or multiplexer it best to decide what supply voltages are available and what signal voltages are required to be passed. This will determine which family you should...
View ArticleClik here to view.
Re: working with AD-FMCOMMS1 at low sampling rate
Hi Dragos, I tried to use dac_dma_setup() instead of dds_setup(), with DAC sampling frequency set to 61.44MSPS.It seems that -although everything was looking good for DDS case- the output of DAC (using...
View ArticleRe: Success story for ADAU1772 in ANC headset
There are successful ADAU1772-based noise cancellation headphones in the market, but we have agreements with those customers to keep their identities confidential.
View ArticleClik here to view.
Re: AD5755: Short Circuit Protection - What exactly it means & How it works ?
Hi Jebas, 1.For the short circuit protection, you can choose the maximum output current to be either 16mA or 8mA. This can be for protection for a short circuit to ground or as a maximum output...
View ArticleRe: Dynamic Range of AD8367
Hi J S Hyanki, The functional gain range is from 0V to 1V, however you can take the pin to 2.5V without harming the DUT. Thanks,Joel
View ArticleAD5254 50K vs 1K
Hello, I ordered two 50K versions of this chip and two 1K versions as well. According to the datasheet (http://www.analog.com/static/imported-files/data_sheets/AD5253_5254.pdf), they have identical...
View ArticleRe: how to burn program into spi flash in right way
Hi Harshit or Analog Device Tech Support, I have BF533EZ_SPI_Programmer_Driver which works for my Atmel AT25F1024 SPI Flash. Now At25F1024 is obsolete. I then found MICROCHIP SST25VF010A for...
View ArticleRe: Can ADV7401 output 720p@30fps analog component with 8bit-4：2：2(DDR mode)?
Hi Ray-san, Thank you very much. Best regards.
View ArticleBF592 EZ Kite Lite SSM2603 max SAMPLE RATE 96000
Hi, im working with the BF592 EZ KIT LITE.I just made a few tests with the audio test programm.I tried to realize a signal generator which uses both outputs and the left and the right channel.It worked...
View ArticleRe: zc702 HDMI broken after update
I had been using the xcomm_zynq kernel branch, according to the information on the wiki (http://wiki.analog.com/resources/tools-software/linux-drivers/platforms/zynq).Using the...
View ArticleRe: AD9129 Evaluation Board & Xilinx ML-605 Reference Design Questions
Reposting my question. Is there a similar register I can write to which allows me to change the digital amplitude of the tone?
View ArticleADV7842 oscillator, XTALP / XTALN
Can I use a CMOS 1.8V oscillator on the XTALP pin (B16)? Or does it have to be differential? I’m looking at Table 100 (unused pins) in the UG-214 manual. It says that B16 and C16 are “always connected...
View ArticleRe: Bug with One Shot blocks?
Hi Christian, I got exactly the same results on my 1701 mini board -- the one-shots do interact with each other in a bizarre manner. Substituting additional pulse counters for the one-shots...
View ArticleRe: Accelerometer and output device for high school physics project
Hi Todd, I cannot make sure who can offer the exact final product that you are looking for. But you can check with the company like sensuss, http://www.sensuss.com/. Thanks. BRNeil
View ArticleClik here to view.
Damping Resistor(s) for MCLK Distribution
The picture below shows a ADAU1401 eval board sending TDM audio to a ADAU1701 on a re-purposed prototype board. Four twisted pairs run the MCLK, BCLK, LRCLK, and TDM data between the boards....
View Article