EVB for high-speed LVDS-to-LVCMOS conversion?
Does AD have an EVB I can use for high-speed multi-input LVDS-to-LVCMOS conversion? I think what I want is a converter that is an LVDS bus on the input side to parallel LVCMOS on the output side. I...
View ArticleRe: Alternative for AD8302
We do not have another phase detector exactly like the AD8302 but with better bw, but we do have the IQ Demodulator ADL5380 that has 390 MHz of baseband bw. You would have to sample the I & Q...
View ArticleRe: ADuCM360.IOVDD. Can I use 1.8V as IOVDD ?
Hi Alex, Thanks for your devoting experiment.And Could you check following my experiment ? Phenomena and views. 1. I've supplied IOVDD = 1.8V and AVDD = 3.3V with Laboratory Power supply without LDO...
View ArticleSPORT stream in simulation reading only LSB
Hello All, I am trying to simulate ADC data coming in to a 21488 via a stream to SPORT1A from a file consisting of a series of 1000 or so theoretical ADC samples given in hex. I got the sample rate...
View ArticleRe: Can ADV7401 output 720p@30fps analog component with 8bit-4：2：2(DDR mode)?
Hello, Thank you very much. Best regards.
View ArticleHow can I get the BF518 demo kit for AVB with the LabX AVB software?
Im looking to get the BF518 demo system thats been put together for AVB and includes a demo of the AVB LabX software.Where from? I cant find it anywhere.
View ArticleRe: SPORT stream in simulation reading only LSB
I just figured it out! I had SLEN set to zero in the SPCTL1 register! Now it's working exactly like it should and I can move forward with my code development!
View ArticleSynchronizing multiple AD9517-1
I am using the AD9517 on two boards, and i am trying to synchronize all outputs such that the phase/timing between outputs on both board are repeatable at every power-up or reset cycle. I have made...
View ArticleRe: What is the failure mechanism of AD9361
Testing was performed using a source delivering power measured in dBm units. It has not been investigated whether failures are due to power or voltage. It is recommended to provide fast acting...
View ArticleRe: AD8131 and AD9461
Hi, If you plan on DC coupling to the AD9467, then you will have to have a signal biased at 2.1V. I am not sure if the ADL5201 will be able to DC couple too AD9467. As an alternative, you could try...
View Article1/f noise vs RMS an peak-peak calculation
Hello, I am in the subject of measuring mV signals with maximum accuracy.The formulas for calculating white noise is described in several data sheets.But for 1/f noise I didn't see such a formula....
View ArticleRe: checkout origin/xcomm_zynq_new_pcore_regmap doesn't work
Hi, The command is `git checkout ...`. Make sure that you have git installed on your machine. - Lars
View ArticleRe: Missing files in latest FPGA release?
Hi, Those files are auto-generated by XPS when you build the project. Alternatively you can follow the instructions on how to generate them manually. - Lars
View ArticleRe: checkout origin/xcomm_zynq_new_pcore_regmap doesn't work
Hi Ken, The command should be: "git checkout xcomm_zynq_new_pcore_regmap" Regards,Dragos Bogdan
View ArticleRe: Accelerometer and output device for high school physics project
Nitzan, See the attached for the reply. Any thoughts you can provide are much appreciated. Thanks, Todd
View ArticleRe: checkout origin/xcomm_zynq_new_pcore_regmap doesn't work
Hi Ken,Are you using a Windows or Linux development environment? If you're using Windows, I would highly recommend using either Ubuntu-12.04 LTS or RedHat Workstation 6.5, since you'd waste a lot of...
View Articlegetting consistent output from ADIS 16375
Hi,I am trying to get data reading from ADIS 16375 through SPI and I was able to detect output (product ID) only once on scope. I have verified that SPI signals from microcontroller are right. I am...
View ArticleRe: Accelerometer and output device for high school physics project
Hi Todd, Would this evaluation system work for you? Nitzan
View ArticleRe: AD7780 only one conversation.
Hi, The differential input voltage range of the AD7780 is equivalent to AIN(+) - AIN(-) = ±VREF/gain. Given a VREF=1V & gain=128, the part can allow a differential input of AIN(+) - AIN(-) =...
View ArticleRe: ADAU1761 Output Dynamic Range and Compressor
Hi BrettG Will the information I have provided enough? With dynamic range and compression on the part of how I should do better? Thank you Paul
View Article