ADAU1442 the spdif maximum sampling frequency is the number?
The spdif input adau1442 --- "output I / O, the output frequency is 192K, but no sound, measurement LRCLK, BCLK, a signal: 192KHZ, 12.288mhz frequency, but the data is not.
View ArticleRe: Odd SPI response from ADIS16488
How long are the leads or cabling that deliver the signals to the IMU?
View ArticleRe: Odd SPI response from ADIS16488
4-5 inches. On Tue, Aug 27, 2013 at 2:46 PM, NevadaMark <
View ArticleRe: AD5700 DEMO BOARD SOURCE CODE
Hi Tracey, Update: I have captured sample data between a HART master and emerson HART transmitter, so I can proceed with my testing even if the AD source code is not available. Mark WaldropSenior...
View ArticleRe: adxl362: trouble getting GUI for eval kit
That was a very good answer, Neil. Could I ask if there is a demo, using this eval kit, that would demonstrate the TAP and DOUBLE TAP functions? Thanks, Tom
View ArticleRe: AD5700 DEMO BOARD SOURCE CODE
Here for others' reference is a sample Command 0 query and response. This was obtained using Hart Tool 2.0 from Triangle Micro Solutions (a simple Hart Master PC program) and an Emerson/Rosemount...
View ArticleRe: Mosfet Drivers help needed!
Hi RSchnell ! I made some calculations and i used as you said the maximum time where the High side was on. The result was a 0.7uF capacitor. So i picked a 3uF and connected it along with an ultra...
View ArticleADV7611 eval board resolution autodetect
Hello, On the ADV7611 eval board, the default bootup configuration seems to be able to autodetect the incoming HDMI resolution and adjust itself on the fly. Is there a set of registers that can be set...
View ArticleRe: ADE7878 SPI communications
Hi Mani, Please find below plots of MISO and SCLK while performing read operationduring SPI mode. In the plot, from the top is the SCLK signal and the onebelow it is the MISO signal. MISO line that is...
View ArticleKC705 + FMCOMMUS1 non-os demo does not compile in SDK
Hello experts, Step-by-step following http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms1-ebz/quickstart/no_os_microblaze but during compilation SDK complains about...
View ArticleRe: bf609 sys_fault and sys_fault_n
Hi, Ronak.Shah, Thanks for your quickly response.After i disable fault input enable(FIEN) bit in SEC_FCTL, uClinux can boot as normal. Thanks.In function init_arch_irq#if 0...
View ArticleAD9629 with Automatic Gain Control @ Input
Hi, i'm wondering if it is possible to use an AGC circuit at the input to the AD9629 (or similar ADC), and somehow control the VGA Gain from a feedback signal direct from the ADC? Does the AD9629 have...
View ArticleRe: How to replace busybox1.18 with busybox1.20?
Thanks a lot!I will do some test and then make the decision.
View ArticleRe: Running the Buildroot image for custom BF537
why you set the loadaaddr to 0x1000? keep it to the default value 0x1000000, try and keep us update, with complete log(instead of sections trimmed from it) in case you still get a fail.
View ArticleADV7611 -HDMI Receiver 5V power glitch
I am trying to capture HDMI error during connection , for one such error is HDMI cable loose connect , so i am planning capture any glitch in HDMI 5V detect signals , how can this be captured , if...
View ArticleAD9467 native FMC: VHDL version instead of Verilog
I've downloaded the included .bit file to check that the AD9467 FMC card is working on the Xilinx Kintex development board (KC705). I was hoping to develop some VHDL based algorithms to test the board...
View ArticleClik here to view.
Re: Problems with multiply - AD1940 on SigmaStudio
Hello GustavoKF, Sorry I didn't understand your application -- I thought you were looking at audio tones, not the low-frequency modulation of your flanger. With the latter, there's no...
View ArticleSD Data Logger mode with spikes(EVAL-ADXL362Z-DB)
Hello all,I'd like to ask you about EVAL-ADXL362Z-DB with SD Data logger mode.I tried DB with following conditions. Battery : coin batteryMode : SD Data logger modeODR : 400 or 200 or 100Range : 2gLow...
View ArticleRe: ADV7623 OSD Resolutions
Hi Wahida, What is repeater software driver?We are only using the souce code generated by OSD tool,though. Regards, Ian
View Article