AD7606 Driver requests probe deferral.
Hi,I am trying to register AD7606 as a SPI platform driver for Intel Galileo board. Kernel 3.8. I have included the AD7606 driver in the kernel build as a built in package, so it tries registering...
View ArticleRe: ADV7619 VSYNC output issue
Thank you for your response. I was able to monitor the mentioned bits. The V_LOCKED_RAW and TMDS_LCK_x_RAW seem to be set all the time. Meanwhile, V_LOCKED_ST should be set only when V_LOCKED_RAW...
View ArticleRe: ADV7181C - Output Data Format
We have a similar application. You may need to run the RS-170 through the CP if you have a video format that is significantly different from the standard SDP output resolutions, which are listed in...
View ArticleClik here to view.
ADAU1452 SPDIF Input issue
Hi, I've built a custom PCB with ADAU1452 and everything is working quite well except for the SPDIF input.I think I've configured everything the way it should be, but no audio can be heard. My current...
View ArticleRe: BF609: second wake-up issue with hibernate mode
Thank you Aaronwu for the answer. 1-Yes we tested only the wake up with push button but the same problem.2-we are working with ADSP-BF609 EZ BOARD. Please can you provide us your uImage to test it in...
View ArticleRe: AD7960 misbehaves
Hi, More information on reference options can be found on Table 8 of the AD7960 datasheet. If the jumpers are on the their default configuration, your setting of enable bits EN2 = 0, EN1 = 0, EN0 = 1...
View ArticleRe: 5 or 6 way crossover-H/W recommendation?
You can potentially store a lot of information inside a single interface read/write; it's 24 (or 28, I haven't checked how it gets stored) bits of data where you probably only need 3 or 4 bits per...
View ArticleRe: AD9361
Thanks for the file, since i currently don't have Xilinx environment any chance you can send a screen shot from the original report? opening this file in a notepad is not clear.
View ArticleClik here to view.
Generation of LFM waveform by using POW under RAM modulation mode in AD9910
Hi everyone, We are planning to use RAM modulation mode to generate LFM waveform on AD9910. We wish to use a total of N RAM addresses (out of 1024) to store the phase offset words. The underlying phase...
View ArticleClik here to view.
Re: Sample Rate on the AD9361
@tlili In the data sheet for the AD9361 under the parameter "Digital Data Timing (CMOS) the spec. is 61.44MHZ but in the section "Digtal Data Timint (LVDS)" the spec. is 245.76 MHz. So is the speed...
View ArticleRe: Power isolation for medical device
Hi, I searched these two transformers in suppliers' website (Farnell, Digikey, Mouser) but couldn't find any. Seems like I need to contact directly to the the manufacturer. Few more questions:Are these...
View ArticleRe: ADV7619 VSYNC output issue
Unfortunately, we do not have an evaluation board yet. Which evaluation board would you recommend? There's a board called Advantiv EVAL-ADV7619-7511, but I think that the 7511 does not support 4k.
View ArticleRe: adv7842
Hi, with regard to application binary? If you are referring to the configuration registers, I have not tweaked any of them. I am running the out of the box programming and running cvbs command only....
View ArticleRe: BF609: second wake-up issue with hibernate mode
Thank you Aaronwu for your supportOur Hardware: - ADSP-BF609- silicon rev 0.2 - The ezkit board 1.0 : BOM rev 1.2For uClinux we are using 2013 blackfin-buildroot.We tested your uImage...
View ArticleRe: AD9739a + ML605 DDR throughput
None of the reference designs meet the requirement- including VC707.It is best to customize so that you will have the required bandwidth.
View ArticleRe: IP3 measurement of ADRF6516
How are you combining the two tones before the ADL5380? Was the -20 dBm number what was set at the signal generator or at the input of the ADL5380? Can you also proved the signal levels, as read at...
View ArticleRe: ADV7623 CEC connection
Hi Ken-more, I've moved your question to the video community - someone should be able to help you shortly. Regards,Rachel
View ArticleRe: 3 Phase Powersupply for Powermeters
David, Good to know! Let me know if you have any further questions. hmani
View Article