Clik here to view.
LIVESPOT=Samoa vs South Africa live
Don't miss watch your exciting sports in Quadrangular Tournament Samoa vs South Africa. Samoa vs South Africa Live Streaming Quadrangular Tournament -match today on your PC.Enjoy Samoa vs South...
View ArticleRe: Some questions about sigmastudio
Hi Tom, Stimulus / Probe now runs up to fs/2 in v3.9 Beta. There may still be issues with the x-axis showing 1/2 or 1/4 the correct frequency, but that's much easier to work around. Bob
View ArticleDolby Audistry is EOL
Hi Brett,I learnt from Dolby that Audistry is EOL. Do you have a plan to support alternative technology from Dolby in ADAU1701?Thanks.Jackie
View ArticleClik here to view.
Precision Current Source
Dear Experts, I have used Multisim 12.0 to simulate a circuit just like shown below.It is a current source. R sensor is the load. The current is set by Vref/Rset.If I used AD8603(V1 is set by 5V). The...
View ArticleRe: The error of converting for AD7657
Hi, We are looking into this. I'll get back to you as soon as possible. Regards,Karen
View ArticleRe: ad215
Hi Kesar, Thanks for considering ADI products on your application. You can acquire samples from your local ADI representative. Contact details for your local ADI salesperson are available via the...
View ArticleRe: ADP5052 PWRGD Question
Hi Jacky, 1, The PWRGD pin is open drain output and its active high voltage depend on pull up voltage. Note that not allow higher than max pin voltage. 2. The table.1 address PWRGD output low with max...
View ArticleData Misalignment Error on Second Iteration
On the second, and only the second, iteration of the while loop of the attached file the call to malloc causes an exception with EXCAUSE 24. This means a data misalignment error. It works fine on the...
View ArticleRe: What is the output of AD9525?
Thanks Louijie,So can you please advice me what I should use so that i get sine wave for about 2 GHz from clock generator. I want atleast 3 output clock generator.
View ArticleRe: ADP5065
When USB (or any 5 V source) is connected to VINx input of the ADP5065 and there is no battery connected, the system output (ISO_Sx) is regulated to 3.3 V typical. Current in no battery -case is being...
View ArticleRe: Second instruction fails on AD7193
Hi Mary, I'm new to ADCs and I am having a hard time to accomplish the very same thing. I thought that would be an easy start but... So, if you look at my Logic Analyzer, is it the 8 extra clock pulses...
View ArticleRe: OP_FORMAT_SEL of ADV7610
Hello, GuenterL-san. Thank you for your response.I understand what you said. It's just notice that SOFTWARE MANUAL lists 0x4C and 0x50 in OP_FORMAT_SEL yet. Thank you!Kikka
View ArticleRe: Register Setting Recommendation of ADV7612 and ADV7611.
Hello, Matt-san. Thank you for your investigation.I understand that we only need to set DIS_I2C_ZERO_COMPR 0x03[7]=1, when it supports the compressed audio. It would be a big help. Finally, please tell...
View ArticleRe: Can I apply voltage to the ADAU1701 SCL/SDA pins when device is powered off?
Dear Brett, Thank you so much for checking with the designer on this important question, and for the two options you have confirmed based on the answer. For existing designs therefore it appears that...
View ArticleDoes AD9129 support signal with 2GHz bandwidth?
I am considering to use AD9129 for my application. There are a few things that I want to know1) maximum data sampling rate (not dac update rate)Our data signal bandwidth is up to 2GHz. So we need to...
View ArticleCapability of HDMI input
Hello. I would like to know the capability of HDMI input of ADI's HDMI Rx devices.It means the pure capability of ADI's HDMI Rx devices without dependence on board layout, power condition and so...
View ArticleRe: Spectral Aliasing.
Hi Haankster, For the example that you give, the aliasing issue won't happen. When you use 400Hz ODR, the internal sampling rate is 3200Hz, 400Hz ODR is got by digital filter. So, for 550Hz vibration,...
View ArticleRe: FMCOMMS1 DAC interface
Rejeesh, See here below how we connected the IP's I attach the complete code for ODDR.OSERDES project is too big if needed we can setup an ftp. Best regards,Daniel
View ArticleWhy memory mapped registers not given as library files?
Hi there, Usually for other micro controllers they used to provide the library files which should have memory mapped registers as in header files for each modules (like, ADC, PWM, UART etc)....
View Article