Re: bf506 TIMER_width and TIMER_Period for AD sample rate
Hi, Prashant my codes is based on http://ez.analog.com/message/46731#46731yes, my question is the sampling rate of internal ADC controlled through ACM, but from the codes, i am confused on the sampling...
View ArticleRe: ADXRS624 - Lowest Rate ?
Hi JoeNova, The lowest rate you can resolve will depend heavily on how well you control other system parameters. Supply voltage and temperature changes, among other factors, will have a large effect,...
View ArticleClik here to view.
Re: how to get total harmonic distortion ................
Hi kishore.r Below is an example experiment that I conducted: Voltage signal appliedAmplitudeFundamental - V1FS/2= 353.55mVrms/2= 0.17677Vrms3rd harmonic - V3FS/10=353.55mVrms/10=0.035355Vrms5th...
View ArticleRe: adau1701 gpio selected level setting
Hi Bob Thanks for your answer. what do configure the DC1? hubijo
View ArticleRe: zc702 HDMI broken after update
The script output is attached. By "our userspace", do you mean that there is a root filesystem provided by Analog Devices? I've been using the old Linaro image referenced by the wiki page...
View ArticleRe: AD9129 Evaluation Board & Xilinx ML-605 Reference Design Questions
How do I connect to the device? The "mrd 0x76000000" command returns:XMD Not Connected to Any Target The commend "targets" returns:XMD Not Connected to Any Target I suspect I have to invoke the...
View ArticleCan ADXL375 BW_RATE register be set to '1111' and still operate I2C at 400kHz?
The BW_RATE register’s Rate bits define both the bandwidth and ODR. The ADXL375 datasheet states that the bits must be set to ‘1101’ (ODR=800, bandwidth=400) to run the I2C interface at 400kHz. It also...
View ArticleRe: ADUM3190 Operation at -55 Deg C
David: I asked the designer and he said that the circuit should operate at -55C. However, some parameters may be out of the datasheet specified range.Regards, Brian
View ArticleClik here to view.
Re: adau1701 gpio selected level setting
Hi, I included the DC Source DC1 to set a minimum level for when the two binary inputs are both off. Use a DC Source anywhere a constant numerical value is needed. The DC Source block lets...
View ArticleRe: ADV212 16bit-RAWPIXEL and JDATA mode problems
Hello DaveD I have got some signals in JDATA bus and the form is almost same like the TechNote_outputformat_ADV202.pdf offers. Anther problem: After the first header of 16 bytes,then comes FF 4F , and...
View ArticleRe: how to get total harmonic distortion ................
Hi hmani, I have assigned HX=2,HY=3,and HZ=4 then the register reading is Register Values HXVHD0.071HYVHD0.467HZVHD0.046VTHD...
View ArticleRe: Can ADXL375 BW_RATE register be set to '1111' and still operate I2C at...
Hi cdarrow, It is totally fine to set ODR = 3200Hz for your application scenario. You can use trigger mode FIFO to record the whole shock or activity profile. Then read the data through I2C interface...
View ArticleRe: ADV7611 :Hdmi signal not detecting in ADV7611
Dear Venkatesh, kindly suggest the what is the hardware issue did you faced in HDMI receiver(ADV7611).Because i am facing the same problem what you mentioned(HDMI input signal not detecting in...
View ArticleRe: AD5504 works, unless I have more than 1
Hi MTJones,I don't know of any reason why it shouldn't be possible to write to multiple AD5504s. Are you writing to the AD5504s individually (individual /SYNC per part) of multiples at once (common...
View Articlehow is the function of the i2s digital out
Hi I will connect an salve to the adau1701 in i2s mode. the resolution should be 16 bit.what must i config wiht the sigmastudio? thanks for helpinghubijo
View ArticleRe: High School Science Project Question about Op Amps?
Thanks Jonathan for the reply. I guess my son and I have a long way to go for learning more about circuits.
View ArticleRe: ADXRS624 - Lowest Rate ?
Dear NitzanInitiallyI want tothank you for thebeautiful answer,andteachingabout thedatasheet.For myapplicationa minimumangularrate of 0.05º/sis enough, butfromyour informationI believeis inevitableto...
View ArticleRe: AD9129 Evaluation Board & Xilinx ML-605 Reference Design Questions
Yes, it needs to be corrected- will do. However, you said the DLL is not locked, that would mean the data was sampled incorrectly. I am a bit confused, can you try clearing that error and see whether...
View ArticleClik here to view.
Re: how is the function of the i2s digital out
Hello hubijo, Here's the settings I have used to transmit I2S audio from a -1701: The MP pins are set up for Output Sdata 0 and 1 at MP6 and MP7. MP10 and MP11 provide your I2S clock...
View Article