Model name of evaluation board (UG-474)
Hell all, The page of AD8139 evaluation boards has a link of UG-474.But I can not find this eval-board in the table which is in same web page....
View ArticleRe: POWER-UP/DOWN SEQUENCE of ADV7181D.
Hello. Thank you for your reply.When you finish double checking, please let me know. Best regards.
View ArticleClik here to view.
Re: ADAU1772 - Active Noise Reduction?
Hi Charles, You can estimate the group delay of any SigmaStudio filter at a frequency of interest by plotting its phase response and approximating its derivative as shown here: Here, the...
View ArticleRe: ADV7630 chip revision codes are different from those described in the...
Hi Davd.Thankyou for your answer.I have understood that there is no other updates to the software manual. Best regards.aimPoint
View ArticleRe: 8221 and input cable length
Emman, Thank you so much for testing it out. The resistors are thin film resistors on silicon die. They are part of a thermal sensor. I spent quite a good amount of time. today, and found that it had...
View ArticleChannel Filter rejection
Hi I'm looking for rejection plots/data on the TX and RX channel filters. In reading the application docs I don't see any reference to these filters except in the Filter Guide where it generally...
View ArticleRe: Aduc7126 IIC problem
HI~PatrickN:I go according Datasheet set I2C1 10bit MODE.I tried to modify the I2C1 128 addresses to use,Master is set to address 128 I2C1ADR0 = 0xF0; I2C1ADR1 = 0x80;Slave is set to address 128...
View ArticleClik here to view.
Re: The HDCP problem about ADV7619
Hi, Dave Why the register HDMI_CONTENT_ENCRYPTED is 0, which indicates input stream processed by the HDMI core is not HDCP encrypted? Does the snow video not have HDCP? And I try the HDCP 1.1...
View ArticleRe: ad7792 kernel 2.x.x driver
I do not know, what backports is.Can you give me any link for example?
View ArticleRe: AD22151 Output Voltage Range
Hi Kris I have a bipolar configuration, with R2 open circuit and R3 short circuit to obtain a sensitivity of 0.4 mV/G. The sensor output is connected to two 16 K resistors in parallel, one connected to...
View ArticleRe: AD8138 differential gain and phase specifications
Hi, John. According to the apps engr of this part, the ADA4932 is the next-generation of AD8132 so it has a little better diff gain and phase errors. But if you will only replace AD8056, then AD8132 or...
View ArticleRe: ADC used for single-pulse conversion
Hi Postino, Here are some list of ADC that could be suitable for your application. You may also wanted to check the ADI website and do a parametric search and put in parameters on the ADC that you...
View ArticleADV7842 Power-Down Sequence
In the datasheet, under the "Power-Down Sequence" section, it says:"The ADV7842 supplies can be deasserted simultaneously as long as a higher rated supply does not go below a lower rated supply." Is...
View ArticleRe: DDS AD9910_PCBZ Single Tone Configuration and Hardware setup Required
Hi, Before I answer your questions, have you verified first if the evaluation board is indeed working before you did external control? It would be worth to do that first. And since you are using XTAL,...
View ArticleRe: Select Inertial Eval Sys
Hello Andrew,Answering this may require contributions from multiple teams, but I can start with the basics. Yes, we have a University program. http://www.analog.com/en/university/topic.htmlFor a quad...
View ArticleRe: ad7792 kernel 2.x.x driver
I can't find drivers that I need on backports site. (drvbp1.linux-foundation.org/~mcgrof/rel-html/backports/)Should I create my custom backports?
View ArticleRe: EVAL-ADIS 64 bit Windows 7 drivers not working
I have not seen this, so I am wondering about the status of the board itself. While we will provide the final answer/resolution on this discussion, I will send you a private message to discuss...
View Article