Re: TDD LTE possibility for AD9361
ENSM control bits are avaiable in registers 0x013 - 0x015. Control bit D2 in register 0x015 turns on both synthesizers (typically used in FDD mode).
View ArticleRe: How does Average/Decimation work on ADIS16223 ?
The destination rate determines the sample rate of the data that is in the data capture buffer. Therefore, it will also the have an impact on the total capture time. I feel like I'm missing something...
View ArticleRe: How does Average/Decimation work on ADIS16223 ?
Hello piyo, Many thanks for your insights! Best regards, NevadaMark
View ArticleClik here to view.
Re: How to receive data continuously from ADIS16223
Hi NevadaMark, Now I realize I should have my own discrete design. Maybe ADXL products will be suitable for my project and analog output will be the best choice to support continuous data streaming....
View ArticleRe: How to receive data continuously from ADIS16223
Hello Jason, Design is always about trade-offs. The ADIS1622x products were designed for vibration applications that do not require continuous data. Machine health and many process variable conditions...
View ArticleCan i download program code to ADSP-CM4xx flash using COM port?
Hello ! Is there any possibility how can i direct download a program binary code (elf, bin) to mcu flash using only serial COM port. I read in hw ref manual about bootloader that permits uart...
View ArticleDAC for sub 1 Volt signal high accuracy signal generation
Dear all,I need to recreate a signal(actually 4 channels at 32KSPS) with +/-150mV swing with an accuracy of 4.5 uV. What are the options available.I am looking for 16 bit quad channel with SPI...
View ArticleClik here to view.
Re: Why bookmarks not work?
I know the Opera is not widest spreading browser. But ...In Linux I have not Microsoft Internet Explorer. Next suggestion?
View ArticleClik here to view.
Re: AD-FMCOMMS1-EBZ input modification
I've been attempting this code, however it always seems to provide syntax errors. I've tried converting the values using "16'h" for Verilog syntax and double checked the begin-end pairs but there's...
View ArticleAD9914 16 QAM
Hello,We are a student team and novices to the AD9914; we have purchased the AD9914 with the evaluation board. One of the things we were looking at was doing a 16 QAM signal and were wondering if...
View ArticleClik here to view.
ADAS1000
Hello ! Before I worked with evaluation board and it worked great.Now I tried with only adas1000 but I get all zeros when I ran the test tone. SPI communication works but receive only zeros. I get for...
View ArticleClik here to view.
Unexpected output data read from ADIS16223
Hi everyone, Today I want to show some capture data that read from ADIS16223. [FIRST]As the picture showed, Z-axis presented stable, but X-axis and Y-axis have a lot of noise. In my code, I read the...
View ArticleRe: Amplitude demodulation
Hi Joelthanks for your help. It looks the correct way.The rotating capacitor is used to transfer signals from a rotating drum where the ultrasonic transducers are placed . Best RegardsMax
View ArticleRe: Unexpected output data read from ADIS16223
I would start by re-reading each buffer to make sure that this is not associated with bad communication cycles, but I will keep thinking about this. I would also make sure that there is zero...
View ArticleRe: ADAS1000
Hello Benjamin, Thanks for your message. Have you issued the same write commands as before - i.e. configure the test tone and then issued the command to the ECGCTL register to start converting data?...
View ArticleRe: ADAS1000
Hello Catherine Thanks for your answer. Yes instructions are just as before. The code works perfectly with Evaluation board.I get directly data from evaluation board. I've waited 30 minutes but still...
View ArticleRe: ADV7612 and ADV7511 reference design questions
Hello, Guenter!Please explain what is the difference between ADV7612 and ADV7511 power supply requirements?Why on EVAL-ADV7612-7511 board power supplies for ADV7612 and ADV7511 are also different?1)....
View ArticleRe: ADAS1000
Hi Benjamin, Thanks for update, when I suggested reading more data, I was thinking more along the lines of a few ms, so if you still aren't seeing proper data for such a long period..then it does...
View ArticleRe: ADAS1000
Hi I have checked everything but it does not work.I have AVDD and IOVDD = 3.3 V.When it comes to ADCVDD and DVDD I have tried both with internal regulator and also an external 1.8V.REFOUT is connected...
View ArticleClik here to view.
Re: How to set the ADAS3023 to start?
Hi,Jcolao, 1. I used a singal generator to make a 1kHZ square wave for [0,1.8V] for my VIO is 1.8v. the picture listed as fellow:2.When it connected with the PD pin, you will find the result as...
View Article