Re: How can I connect the not use pin for AD8436?
Hi, Kaos. Apology for the delay. May I know what AD8436 package are you using? Regards,Anna
View ArticleRe: hanging at the adc testing instruction adfmcomms1ebz
sir the images are attached below. thanks, gitanjali
View ArticleRe: adau1761 on ZedBoard(no linaro)
HI Lars,Are you referring to the h/w design cause we have matched one with HDMI design and done no modifications in it. Please suggest. Also I wanted to get clarification on U-Boot.elf. The one which...
View ArticleRe: Thermal diode sensor offset
Hi Christian, The equation 2 mentioned in the Application Note EE-346 on Page 5 is wrong. The equation 3 used is correct. You can see the correct formula on page 14 of the ADM1032 datasheet . The link...
View ArticleRe: Build Blackfin 527 ezkit with video support (u-boot splash screen)
Could you run "make bf527-ezkit" with our standard release code, as described in http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:compiling, and update us the result? Note if you...
View ArticleRe: JTAG console fail on win7 (bfin-gdbproxy.exe)
And also that is not a problem with win7, I tried on windows xp, It was the same behavior.
View ArticleRe: ADA4940-2 noise issue
Hi Tom, Do you have an RC low-pass filter between the ADA4940-2 and your ADC? It would be great if you could provide your circuit schematic. You can also try the free ADI DiffAmp Calculator or the NI...
View ArticleClik here to view.
BF609 PIXC DMA LIST 读取错误。
BF609 PIXC DMA LIST 读取错误。 我的链表配置方式如下： /* DMA descriptor work unit for PDMA */typedef struct{ volatile void *pNextDesc; /* Pointer to next Descriptor */ volatile void...
View ArticleADC7762 on board differentail amplifier
I am seeking performance specification for the on-chip differential amplifier on the ADC7762, in particular the maximum and recommended voltages for VinA+ (Pin 19) and VinA- (pin 20). The data sheet...
View ArticleADV7280-M Driver
Hello! Do we have the ADV7280-M Linux or Android Driver for customer? Thanks for your support
View ArticleRe: BF609 PIXC DMA LIST 读取错误。
链表部分拷贝错了。应该是：//输入的UYVY图像背景 OSD_DMA35_DescriptorCopy[0].pNextDesc = &OSD_DMA35_DescriptorCopy[1];// 下一个描述符地址 //OSD_DMA15_DescriptorCopy[0].Config...
View ArticleRe: SigmaDSP Performance Overview?
Hi Juergen, The two tables list different characteristics because of the fundamental difference between the SigmaDSP and SHARC. The performance of SigmaDSPs is measured not by benchmark...
View ArticleRe: ADV7511 linux video driver, monitor "Out of Range"
I reconnected the 1920x1080 monitor, and then it's also set to 33MHz. Strange.
View ArticleRe: ADV7511 linux video driver, monitor "Out of Range"
Hi, Are you using the right combination of axi-clkgen core and driver? There is a v1 and a v2. Is it possible that you have a v2 in your design but a v1 configured in your devicetree? - Lars
View ArticleRe: AD-FMCOMMS1-EBZ input modification
The SED failure is because you have hard coded the values. It may be better to keep this check ON.Can you use the DDS enable signal to drive these values (BTW, why are you giving a DC offset)?
View ArticleRe: hanging at the adc testing instruction adfmcomms1ebz
All I see is "DATA", "DATA_PORT", "DATA_PORT_1"...... and all we will do is make this thread longer.Let's try this in a different way. Can you post the changes you made to the reference design?
View ArticleRe: A quick question about the EVAL-CED1Z
Hi Jesper, EVAL-CED1Z is used only in a small number of ADI evaluation kits – such as AD7760. It is not used on any of the high speed converters and hence it would not be compatible. For any work in...
View ArticleRe: Vrms calibration in ADE7758_SPI with Arduino
Hi Dlath, Yesterday when I re-tested my ADE7758 using the same code as previous one (reply posted on 28 Nov) to check whether it is working as expected. However, when I read the AVRMS register, the...
View ArticleRe: type of interface in dds ic ad9959 to generate a lfm signal
Hi Rahul, It is preferable to use the 4 bit serial mode since it offers the fastest data rate. The fpga has a lot of I/O so this capability is best exploited by using the 4 bit serial mode. If you want...
View ArticleRe: hanging at the adc testing instruction adfmcomms1ebz
sir,if you can see on each images i have given the name of the signal i'm monitoring.and in the second last post ihave posted the hex values recorded for each signal that i was monitoring.i wanted to...
View Article