reference design for ic DDS IC9959
hi guies have you a reference design for DDS IC AD9959. i have with me this IC and its evaluation board. I am sure reference design would help me a lot at my beginner stage. regardsRAHUL...
View ArticleNational Instruments ADI free software
The ADI web site states that: "A free, downloadable version of National Instrumentations Multisim 11 Circuit Simulation Software, tailored for evaluating ADI components." I downloaded the software and...
View ArticleRe: How to use the Wind Noise Suppressor module
DearBrettG Could you reply the above questions？I am looking forward the help from you！
View ArticleRe: ADE7753 Voltage Attenuation with non-isolated supply
Hi Hmani, Thank you for the clear explanation regarding the AGND/DGND connections, very helpful. For the voltage monitoring, the application is for a utility, and the input power will vary, in some...
View ArticleRe: need video decoder IC which is industrial grade
I have to record the DVI-A (5 signals R,G,B,VS,HS) or DVI-D ( differential CLK,D0,D1,D2,DDC CLK ,DDC DATA).
View ArticleRe: need video decoder IC which is industrial grade
my processor accepts 24 bit data only
View ArticleIs it possible to have simultaneousely H, V ,F signals at the output of ADV7612?
Hello! Is it possible ( but maybe undocumented ) to have simultaneousely H, V ,F signals at the output of ADV7612?If not, then what AD HDMI receivers have simultaneousely H, V and F signals at its...
View ArticleHow to receive data continuously from ADIS16223
Hi, everyone. The question is same with the title.There are three parts in my code: capturing, receiving and transmitting.[CAPTURE]: Start to capture data[RECEIVE]: Read data from ADIS16223 SPI...
View ArticleRe: A quick question about the EVAL-CED1Z
Hi Johnny, Thanks for your reply - although not necessarily what I had hoped for ... Might you recommend another interface between the AD7760 eval board and the computer that does also work with higher...
View ArticleAmplitude demodulation
Dear allI'm modulating a 1.1 GHZ frequency with the ADL5391 with an input analog signal of 10 to 20 MHz bandwidth. The result is a 1.1 GHz AM modulated carrier and it's sent through a rotating...
View ArticleRe: HOW TO ACQUIRE A 5 MHZ 0-10 VOLT SIGNAL
Dear Karen, Thank you for the help ,I m going to use AD7357 with CED board for acquiring 20mv -1.5 VAC Signal. Thanks for your support. Best Regards, Rahul Vijay
View ArticleRe: ADV7403:Input DC level fluctuation with CVBS input
Can we get some more information on this? 1) Where are you measuring the DC level at on the schematic. The CVBS input is AC coupled2) Which bias are you changing??
View ArticleRe: L1 data SRAM status after software reset
Thanks for the info. While waiting for a reply I had run a test and it seemed to work, but it's good to have confirmation.
View ArticleRe: XTAL input of ADV8003
I believe it will accept a 1.8V oscillator input on XTALP with XTALN left floating however I will forward this question to the ADV8003 expert to verify.
View ArticleADF4158 PLL Software
I am working with ADF4158 Evaluation board. I just downloaded a newer version of ADF41589 PLL software (Revision 4.9.0). The main controls section Register 4 doesn't allow me to choose a CLK2 Div value...
View ArticleRe: Signal latancy in the ADV7181C and ADV7392.
Latency through the devices are dependent on the format and which features are enabled. Case in point, the ADV7181C has a 2D comb filter which can delay up to a line. Therefore it is difficult to...
View ArticleRe: ADF4158 PLL Software
Either CLK1 or CLK2 must be greater than 1; i.e. CLK1 and CLK2 cannot be 1 at the same time. The software enforces CLK2 > 1. It will be added to the next revision of the data sheet. I will also...
View ArticleRe: Optimization using pragma's
Hi Chad, I think some issues have been mixed up.At the outset I asked a question on "Optimization using pragma's", which wasanswered by Michael. Then I was faced with another optimization problem,...
View ArticleRe: Optimization using pragma's
Hi Reinier, Sorry for the confusion. You're absolutely right - PR72292 concerns your ability to use PGO, and we have reproduced your problems here and found the root cause. This issue will be addressed...
View Article