Spin the motor with ad-fmcmotcon1-ebz
I have a ad-fmcmotcon1-ebz. I have limited space on my desk, and I don't have another monitor, keyboard, mouse, hdmi cable, etc, so I am hoping I can spin a motor though the web interface or command...
View ArticleRe: Reading ADIS16480 Accelerometer Data with the Arudino Uno
when i connect ADIS16480 LED2 blinks and LED1 is not glowing at all and screen showing couldn't found device rescan.after rescanning also my PC is not able to find ADIS16480. couldn't able to find out...
View ArticleRegarding "Earthing of isolated circuits" in measurement applications like...
Respected Sir,I am on the verge of completion of an 8-channel analog input module design. Each channel can measure RTD Pt-100, Thermocouple (J,K,R,S,T,B,N),0-10VDC and 0-20mA input types. A 24VDC...
View ArticleRe: Reading ADIS16480 Accelerometer Data with the Arudino Uno
I would start by taking the ADIS16480AMLZ off of the EVAL-ADIS and then plug it in again. Another thing to think about is the USB connection. We have had some challenges with the cables from time to...
View ArticleRe: problem about FS baud rate for ad9789
Now, DDS output frequency is 100MHz,the center frequency of BPF filter is 100MHz, but No output！why?the following is the content fo the...
View ArticleRe: Spectrum of Quantization Noise?
I have doubts on Davids explanation too. Imagine a "perfect" ADC without DNL and noise and apply a linear voltage ramp to the input. Then the quanization noise should manifest with a...
View ArticleADE7878 AVDD DVVD error
I powered up ADE7878 with a development board and measured AVDD and DVDD. Non of them shows 2.5V .I connected PM1 pin to ground circuit , the IRQ1 interrupt pin drives low , REF in/out shows 1.2 V but...
View ArticleClik here to view.
Explanation of different parameters on EVAL AD5933EBZ Software and its...
Dear Friends, Please explain different parameters of Evaluation board EVAL AD5933EBZ software(From left to right) like Sweep parameters(Start Frequency, Delta Frequency, Number of Increments, Number of...
View ArticleRe: How to build the Eval AD5933 drivers with IAR Workbench
I think we'll look at using the AD5933 on a different control board that closer matches our needs. Thanks
View ArticleRe: Problem about the differential outputs of ADRF6510
Hi Joel, Thank you for your help! I only have the oscilloscope with single-ended inputs and would like to use this oscilloscope to measure the differential outputs of ADRF6510. For differential...
View ArticleRe: Spectrum of Quantization Noise?
In response to Achim; the ADC output is sampled-time, so all those harmonics alias back into the Nyquist zone in random places, unless the sawtooth and ADC sample frequencies are related. This makes...
View Articlehi.in ADI Water Analysis Solution for pH Meters.pdf there is a block in the...
hi.in ADI Water Analysis Solution for pH Meters.pdf there is a block in the name of programmable ac current in conductivity meter . i can not understand why there is not a single current source for that
View ArticleAD844 CFOA
I want to purchase AD 844 current feed back operational amplifier, But i am facing a problem while doing simulation part on PSPICE simulator. It is written in data sheet that in case of CFOA current at...
View ArticleADV8003/ADV8005 DDR2 Memory interface need not VTT power supply
Hi, Checked ADV8003 EVB OrCAD schematics, DDR2 Memory interface have not VTT power supply, Is it integrated into chip?
View ArticleClik here to view.
How to deal with ADV8005 EXT OSD and TTL input interface pin if unused
Hi, As ADV8005 hardware manual descriped, ADV8005 EXT OSD and TTL input pins need "Connect this pin to ground through a 4.7kΩ resistor" if unused. but it will increase much more resistors in PCB...
View ArticleClik here to view.
Re: AD844 CFOA
Hello divyanakra, the current flowing into the low impedant pin 2 of the OpAmp will always be mirrored to node 5 of the simplified schematic in fig. 31 of the data sheet. So in your words: Iz will...
View ArticleRe: for 1080p30 and 1080p29 adv7611 DE line problem
Hi Praveen, I was using the software driver to configure EVAL-ADV7612-7511 and EVAL-ADV7611EB1Z. I'm thinking you will probably want to purchase one of these. For HDMI generator, I was using Quantum...
View ArticleAnalog tools integration support
Hi every body I need some help: Right now we are working in a migration project, where analog devices toolsneed to be enabled in the operating system Xillinux (Ubuntu OS withXillybus tools) and we need...
View Article