AD9361 phase noise at 2440 and 4880MHz
I've noticed higher LO phase noise at 2440MHz and 4880MHz. I initially thought it may be caused by frac-N boundary spurs since it is near an integer multiple of the 40MHz ref frequency, but 4840MHz is...
View ArticleRe: edit hardwareconfiguration in graphical sigma studio?
Hello Bob Thank you for the answer. Is it possible to edit the register in the graphical mode to change the register value? Is it possible to select the bit in the register with an "module" in the...
View ArticleRe: ADL5391
Dear Joel, The correction suggested in the datasheet was actually right, but we placed the 50ohm termination (over R2) in a wrong way. That should explain our results, Anyway thanks for your helpFabio
View ArticleRe: ADV7611 i2s audio problem
If this is your first project with ADV7611, I would strongly suggest you purchase EVAL-ADV7611EB1Z or EVAL-ADV7612-7511. It will be useful for you to have a platform with known-good hardware/software....
View ArticleOp Amp for Low Current (< 100 mA) Measurement
I am trying to measure the current going to a 3 W DC motor. The motor draws less than 100 mA, what would be the best op-amp circuit to use? Or what would be the best solution to tackle this problem?
View ArticleRe: Analog tools integration support
Hi Dennis,Thank you for your inquiry. You have asked your question in the general help space for EngineerZone. I am moving your question to the FPGA Reference Designs area for assistance.Regards,Lisa
View ArticleClik here to view.
Re: ADM6713 Absolute Maximum Ratings Question
I’ve checked on this and the abs max ratings on these datasheet are not “tested”. They come from the process parameters used for these parts. The 25degC test condition is not appropriate. The abs max...
View ArticleRe: ADXL362 rotate motion
Hi Neil, Thanks of your reply.How are about "tilt" sensing?Regard,Kevin
View ArticleAD9364 Clock
I have this question about clocking data into the AD9364. In the AD9364 Reference Manual UG-673 document, on p.87 and p.99 it says that " Note that FB_CLK must be a feedback version of DATA_CLK (exact...
View ArticleRe: AD5621 Offset Voltage
Hi Reinhard, The data from spec table comes from Yield Analise, that analyzed hundreds of samples form different wafers.The plots come from a single device that may or maybe not fit within typical...
View ArticleRe: AD9833 - output failure
Hi All, The problem looks quite "strange", if register 2 works fine, there is not reason why the register1 cannot operate correctly.May you use a fresh part and try again, please? Regards, Miguel
View ArticleControl of Boston engineering FlexMC kit with ADI CM408F
I am working on the FlexMC kit(Low voltage inverter for BLDC motor) from Boston engineering which is coupled with the ADI CM408F . The FlexMC kit comes with the simulink example which implements the...
View ArticleRe: AD9364 Clock
Hi Anthony,You have asked your question in the general help space for EngineerZone. I am moving your question to theMicrocontroller no-OS Drivers space for assistance.Thank you,Lisa
View ArticleRe: A question about AD-FMCOMMS1-EBZ
Hi Sir, We also used for below ways to verify this issue but it seems not be solved a.ML605+S1(revC) and software is XPS/SDK 14.6ADI hdl...
View ArticleRe: Would like to stream file output from the EVAL-ADISZ
NevadaMark, Sorry for the confusion of names but for some reason I'm logged with another user name, no problem. Anyway the Data Capture works fine and I can off load the data. Thanks Mark
View ArticleClik here to view.
Have a ADIS16364 IMU with the EVAL-ADIS, stalls waiting for transfer from SDP...
As the title says I'm using the ADIS16364 IMU with the EVAL-ADIS evaluation board, which just arrived today. When "Read"ing the data output on the GUI, everything is fine. I can track all three gyros...
View ArticleRe: SIC_ISR Registers set to zerp when MCMEN bit enabled
OK, I was hoping for a dump of all the SPORT registers and their settings, but I will try to respond given the subset you provided. It is important to note that in multichannel mode, it is the RFS that...
View ArticleCan we make ADV7626 just pass the AV mute ON bits to sink without sending...
Hello, I saw ADV7626 always sent out the black video when it received the GCP with AV_MUTE_ON bits from the source device. Is there any register in ADV7626 we can use, which, let ADV7626 just pass the...
View Article