Quantcast
Channel: EngineerZone: Message List
Browsing all 36216 articles
Browse latest View live

Re: AD8237 Gain/Bandwidth problem

Hey Achim thanks for the reply!  I'm actually just trying to design a circuit for 0-3.3V sensors so I don't really need a negative Vs- thats why I just set it to ground.  The issue in my lab is that my...

View Article


Re: AD8237 Gain/Bandwidth problem

Hello, you have an AC-coupled signal path. No matter what you apply to J17, the series capacitor will always block the DC-portion of your input signal. So the + input of the AD8237 (pin 2) will always...

View Article


Re: AD8237 Gain/Bandwidth problem

Yess!!  It looks like you called it.  I added the bias to pin 2 and the wave form looks good at 20kHz.  The gain is set to 6 and I'm running the same 100mV 20kHz wave through.  So I think this design...

View Article

Image may be NSFW.
Clik here to view.

Re: AD8237 Gain/Bandwidth problem

Pic of the current wave form... 

View Article

Re: AD7656 Vdrive issue

A sequencing test was performed with a conversor never used before. No analog input signals were supplied. Order:  1) VDD/VSS2) AVCC/DVCC3) Vdrive Results: Vdrive with VDD/VSS supplied = 0VVdrive with...

View Article


Re: AD8237 Gain/Bandwidth problem

Hi Robbie, Thank you for using ADI products on your circuits. What specific application are you doing? I am glad that you already make your circuit working. But I would like to take this opportunity to...

View Article

How to set the filter, gain and read the RSSI

Hi all,     I had realized the point to point communication of AD9361. But in my program I don't know how to set the lowpass filter, hardware gain(TX and RX) which used to increase the transmission...

View Article

Image may be NSFW.
Clik here to view.

Re: AD8237 Gain/Bandwidth problem

Ok cool.  I checked it out.  How should I read the operating range?  My configuration would be the 8237 with V+=3.3V and V-=0V.  It gives me an operating voltage level from 1 to -1 common mode.  My...

View Article


Re: AD8237 Gain/Bandwidth problem

Where is the create button?  It sounds dumb but I can't find it on here.  It may be easier for you to PM to start it and I can reply with a pdf.

View Article


Re: AD7793 EVB Source Code

Hi Kris,I have sent you an email with information which you might find useful. Thanks and Regards,Jarwin

View Article

Image may be NSFW.
Clik here to view.

Re: adv7280-M CVBS(NTSC) input issue

1) When you fed the CVBS source to the television you did not see the noise. Correct ?    Did you feed the CVBS signal through the same  YES2) The oscilloscope plots show high frequency content,...

View Article

Re: Any Analog Devices DSPs with LVDS input?

I don't know of any ADI DSPs with LVDS inputs. Certainly none of the SHARCs have this feature. We use LVDS routinely with SPORTs. You will probably need a Quad Receiver. There are several choices. The...

View Article

Re: Bitstream from EVAL-CED1Z

Hi mhay,We are looking into this. We'll get back to you soon. Regards,Jarwin

View Article


AD9257 Handling of the VCM pin

Hello support team, This thread is one that is related to the AA.I've created a new discussion for the following questions.Please advice the these questions. When I power down the VCM pin by Register...

View Article

Re: AD9257 Processing of the VCM pin

Hello Dougl, I've created a new discussion for the above questions.https://ez.analog.com/message/158655#158655 Could you please support this discussion? Thanks,Tak

View Article


Re: I2C with ADSP21477

Hi Tim,You can find an application note “EE-346” and its associated example codes for interfacing temperature sensor using TWI. I hope this will help you.You can find the application note and its...

View Article

Re: Bitstream from EVAL-CED1Z

Hi Jarwin Tee, Thank you in advance. Regardsmhay

View Article


Image may be NSFW.
Clik here to view.

Re: AD9833 - output failure

Hi Remi.I used evaluation board of AD9833 to write a 149kHz output.Below are snapshots during debug mode:1.Enter reset mode2. D13 bit is set to enable 2 write operations3. Frequency Register write:...

View Article

Re: AD9674 init problem

Hello Marcin, I hope you have managed to get the data coming out of your AD9674. I am also testing a new board with two AD9674's and having problems.  Having previously developed a product using the...

View Article

Re: Linux OS Booting Fail

Hi, Lars, No, :-( Regards tasi

View Article
Browsing all 36216 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>