Re: MAT14 vs. MAT04
Hi, Ricky. Sorry for this inconvenience. I have not received any feedback yet. Regards,Anna
View ArticleRe: How to deal with the failure report by physdiskwrite.exe during the...
Hi, Larsc Thanks for your help. I installed an XP-sp3 system with .Net framework 3.5 software. I followed the instructions on the webpage, but "list disk" failed to find the SD drive. I found some...
View ArticleRe: Better opamp then the AD8045
Hi Ronald, Which specifications of the AD8045 are you particular with? I would imagine that the op-amp you want would have high bandwidth and a fast slew rate. You could check out the ADA4817-1. It...
View ArticleRe: When ADV7390 outputs PAL, is Closed Caption invalid?
Hello, Thank you for your reply. I checked other datasheet about this.Datasheet of AK8813 says that closed caption data is inserted to line 22 and line 335 in PAL.(I don't know whether it means...
View ArticleRe: How to measure the impedance charactersistics of a unknown valued...
Thank you very much for your response. I have an other question. What do you mean by calibration setup ? Do I need to calibrate the board every time I set up ? For Example, I have put 15 pf capacitor...
View ArticleRe: Abort counter enable feature of SMC.
Hi Nabeel, I have a customer using the same Nor flash part number with EZKIT on BF609, the Nor flash part schemetic is almost the same with BF609 EZKIT except that on customer's board, there is no...
View ArticleAD7793 EVB Source Code
Sir,I am using AD7793 EVB and need Labview source code to check SPI communication codes.Could you give me that? Thank you.Kris Huang
View ArticleClik here to view.
Re: ADV7619:What timing is "VS InfoFrame Registers" update?
Hi GuenterL-san. Thank you polite answer. Best regards.aimPoint
View ArticleRe: Auto detect input
Hello Graeme, Analog Digital | Select--------------------------------------------< Thresh < Thresh | Analog< Thresh > Thresh | Digital> Thresh < Thresh |...
View ArticleRe: Auto detect input
Hi Chris, That looks like its going to do the job, I'm only mono on the input so I'm guessing i can just remove one line from each Graeme
View Articlead9467_fmc on the Zedboard
I'm trying to implement the ad9467_fmc project on a zedboard, but had to make some changes to the zed_system_bd.tcl script to get it to compile correctly. I mainly want to make sure the changes I made...
View ArticleRe: Auto detect input
Yes, and reduce the SignalDetectors by one so each has only one input. Chris
View ArticleRe: What is output of ADA4691-2 in Shutdown?
Hi Satoshi, I haven't yet hear any responses from the product owner of this part. I am really sorry for the delay. But I will let you know as soon as I get the information that we need. Best regards,Emman
View ArticleADM6713 Absolute Maximum Ratings Question
ADI Technical Support, I have a question about absolute maximum ratings (AMR) published on the ADM6713 datasheet. If you review the section that lists the AMR, an ambient temperature of 25C is listed....
View ArticleRe: AD9361 Sensitivity based on TDD & FDD
If there is a difference it will be chip configuration dependent and mostly due to spurious from the digital section and spurious generated from different portions of the chip. I would recommend...
View ArticleRe: AD9361 clock BBPLL frequencies for digital TV
My previous post covers all the constraints and available adjustments. UG570 describes ref clock frequency range and phase noise characteristics to achieve datasheet specifications.You need to see...
View ArticleClik here to view.
ADV8005 Firmware 1.80RC3 compilation
We are trying to compile the source tree for the ADV8005 evaluation board that has the BF524 part. We are using the "bf" toolchain and using "cmake -DPRODUCT=8005_avr_7625_bfIs this the correct...
View ArticleRe: AD9361 : RX and TX using the same LO
Rx and Tx LO frequencies are generated by dedicated RFPLLs. One for Tx and one for Rx. They can be set to the same or two different frequencies. BBPLL is common to both and is used to create all...
View ArticleRe: AD9361 ssues with q0/i1/q1 on latest kernel and Vivado HDL
I'm finally now up to date with both the ADI "linux" and "hdl" (with pcore v8) repos. I did add "adi,tdd-use-fdd-vco-tables-enable" to my devictree, but I still had to make the following changes to...
View Article