Re: I2C to SPI bridge for AD7176-2
Hi tariqa, We are looking into this. We will get back to you as soon as possible. Regards,Jarwin
View ArticleRe: question about U-Boot and USB page
Hi Matt, could you attach a complete boot and operation log for the encountered issue? Also double check if you are using the correct USB adaptor connector.
View ArticleRe: Using an AC excitation in other ADCs not the AD7195.
Hi Robert, We're looking into this. We'll get back to you as soon as possible. Thanks and Best Regards,Chris
View ArticleRe: AD7949 command set
Hi Karen, Thank you for your reply. But what I am looking for is the command set to direct the ADC to measure a particular channel. Does ADI have this set of command available for AD7949?
View ArticleRe: AD9361 - IIO Oscilloscope
Dear tlili, I was trying to demodulate an FM broadcast program when I saw the relative program spectrum mixed into the baseband.I wanted to save the spectrum and I clicked "Save as" in the File menu...
View ArticleClik here to view.
Re: About MP pin setting and highspeed slave mode setting in ADAU144x
Hello Takepiro, 1. There are no internal pull-ups on the MPx pins when configured as inputs. 2. These registers can be configured in SigmaStudio under the Hardware Configuration Registers window...
View ArticleRe: AD9912 I use spur killer, I need killed spur harmonic 2, It should write...
Hi Grisha, For register 0x500, load the harmonic value. In your case it would be value 2. The since you need to enable the spur reduction function for spur A, you need set bit 7. All together, you have...
View ArticleClik here to view.
Re: ADV7511 Xilinx Reference Design for Zedboard
Hi, May I know, how to replace the original IMG_DATA (cf_hdmi_demo.h) with other image? ThanksWira
View ArticleRe: ADXL001-70z eval board noise on unfiltered XOUT
Hi Jasper, If there is no filter at the XOUT, you may see the ADXL001 clock noise. As you mentioned, you can add a low pass filter (15kOhm // 1nF) between ADXL001 output and amplifier. Actually, this...
View ArticleRe: ADXL001-70z eval board, do I read the values correctly?
Hi Jasper, 1. If you have vibration table, you can trust its output to test ADXL001.2. If you want to use other vibration meter with ADXL001, I would suggest piezo sensor, please choose light piezo...
View ArticleRe: How to measure the impedance charactersistics of a unknown valued...
Do you have the AD5933 evaluation board (EVAL-AD5933EBZ) with you?The AD5933 evaluation board is a test system designed to simplify the evaluation of the AD5933. Or are you going to design your own...
View ArticleRe: connecting two 3-wire RTD to AD7793
Hi, You can probably refer to this: CN0287: Isolated 4-Channel, Thermocouple/RTD Temperature Measurement System with 0.5°C Accuracy This is similar to what you are looking for except it uses an AD7193...
View ArticleRe: How to measure unknown impedance using AD5933 EBZ ?
Hi, You may start by referring to AD5933 evaluation board user guide: http://www.analog.com/static/imported-files/user_guides/UG-364.pdfThe "performing a frequency sweep section" gives detailed...
View ArticleRe: TX/RX Path Setup
Thanks for the update.Initialization now runs without error using the modified input parameters above.Thanks for the help.-Allen
View ArticleRe: ADE7880, Can't get ZXTOVA, ZXTOVB, ZXTOVC flag at STATUS1
Hi hmani, Thank you very much for the help. Upon the data sheet, Rev. B, here are the setup during the power up initialization: 1. check IRQ1 line (status1/ mask1), wait until it is low, then read...
View Articlewhat's the trigger name of ad9361?
Hi all, When I write a program to realize point to point communication, I need set the ADC and DAC triggers, but I don't know the name of triggers when I use the function...
View ArticleClik here to view.
Re: EVAL-SDP-CB1Z board with the EVAL-AD9837SDZ board
Hi,I have tried to replicate your set-up with 0.2MHz output.Please see snapshot below:But there is an output signal at VOUT pin.Can you check the continuity between pin10 (VOUT) of AD9837 IC and VOUT...
View ArticleClik here to view.
Who can tell me the differences or relationship of ad9361-phy and...
Who can tell me the differences or relationship of ad9361-phy and cf-ad9361-lpc and cf-ad9361-dds-core-lpc?Thank you
View ArticleRe: The ADV7619 with the input source of 4K*2K
I'm not sure why two ADV7619 devices would be required. Do you have a block diagram for what you are trying to do? -Matt
View ArticleRe: AD7799 data stability
Hi Morteza, The load cell looks okay. How is the load cell connected to the ADC? Thanks and Best Regards,Chris
View Article