Re: ADV7625 OSD Text characters are not clear during emulation and...
Hi All Sorry,I forget to update the firmware files in the folder.Now it test normal run at my machine.Thank you!
View ArticleRe: Problems with SPI slave boot on ADSP-21479
Hi, having read through some other posts regarding the slave boot problem, I tried to check whether the boot kernel itself executes properly by recompiling 479_spi.asm and seting a flag high at the end...
View ArticleRe: ADV7625 OSD Text characters are not clear during emulation and...
Thanks very much for the status update and good to know that the problem is resolved finally. When you have any new problem, please start creating new thread and we can close this. Best...
View ArticleClik here to view.
Re: AD5755 unusual behavior for the 1st channel
Hi, I have some several questions regarding the setup if you wouldn't mind. Have you tried checking if the FAULT bit is up? Also, would you be able to share if there are any difference in the...
View ArticleRe: ADE7753 Sample sequence
Hi Christian I am glad you are able to get it working. Do you have the HPF enabled in the V1 channel? Try enabling it to see if the offset goes away. Anyways, you can compensate for the intrinsic...
View ArticleRe: ADSP-21489 tdmi Jitter
Hi Itamar, Can you provide the screenshot of the CLK,and FS signals and also the TDV signal of both SPORT 2 and 3.What is your SPORT configuration or Can you share the C code used for SPORT...
View ArticleRe: AD21489 I2C NACK handling
Hi Frank, What is the value of the TWIMSTAT register when you do a TWI write with a bad slave address ?You may have to Write 1 to clear the TWIANAK bit Regards,Mahesh
View ArticleRe: Problems with SPI slave boot on ADSP-21479
Hi Chris, The default setting of SPICTL register during SPI Slave Boot is 0x4d22 and the MSBF bit is cleared.So it is LSB first. But the Host is sending data in MSB first format.Hence you have to send...
View ArticleRe: ADV7181C Analog RGB
Dear dave, Thanks for your reply there is any setting i can do to decode 768 x 576 pixel 625i RGB on ADV7181 chip.Please Suggest us regrading 768 x 576 pixel 625i RGB decode.there any other devices...
View ArticleRe: ADV7181c
Dear GuenterL, Thanks for your reply My Analog RGB input is 768 x 576 625i. i couldn't how to set to this pixel input decodeCan you help me with this Thanking youRegards,Balaji
View ArticleRe: Flash programming in ADSP21489
Dear Sir, In our design, we are using both ADSP21489 and Spartan FPGA to cater our application requirements. we proved the functionality of our design when both programs loaded through JTAGs. Now, I'm...
View ArticleADIS16209
I use ADIS16209 evaluation board with TI controller. I not set means not write any control register & assume that it is ok as per datasheet.1. My target is to measure X or Y axis both side with...
View ArticlePin Muxing in CCES 1.1.0 for ADSP-BF538F
Hi All, I am using the black fin processor ADSP-BF538F in one of our project. I am using the cross core embedded studio 1.1.0 IDE for my development. I followed the procedure to create a cross core...
View ArticleClik here to view.
ADRF6518 output noise, dBV/Hz or dBV/sqrt(Hz)
hi; I saw the output noise density of ADRF6158 is -104.6dBV/Hz, but the unit in datasheet of ADRF6516 is dBV/sqrt(Hz), what is the different between? or just a print error in datasheet of ADRF6518, it...
View Article3 Phase Powersupply for Powermeters
Hi, IEC62053 states that a meter must be able to operate fromany single phase with 70% nominal voltage. My first idea was to use 3 small transformers to get this done,but is there a smarter solution...
View ArticleRe: Q. About ChipScope and Vivado data capture
I'm using FMCOMMS2 + ZC702. that would not be helpful to me..
View ArticleADIS16480, Datasheet Error
Hi Mark,I think table 94 in the datasheet is wrong after some tests. I think EKF_CNFG[1] = 1 means disabling, while =0 means enable. Regarding other bits in EKF_CNFG, i am not sure whether the...
View ArticleADIS16480, EKF_CFG[0] vs EKF_CFG[9]
Hi Mark,One more question,Is there any difference while observing pitch and roll angles, with regard to different EKF_CNFG[0] / EKF_CNFG[9] settings? After some simple tests via EVAL_ADIS, I don't see...
View ArticleClik here to view.
Are I and Q completely independent?
i adjusted adc_init like this and this is Vivado's capture. Does this mean I and Q are not separated completely?
View ArticleRe: ADIS16480, SYS_E_FLAG[4], Source of over-range?
Thank you! We appreciate your message about organizing your questions. Since you mentioned that, our preference is that each discussion present only one question, so that the follow-up discussion can...
View Article