Clik here to view.
Re: ADV7611 : Current consumption of XGA？
Hi DaveD & GuenterL Thank you answers. Best RegardsaimPoint
View ArticleRe: Re: How to do a mass erase in boards other than the evaluation boards?
I am not able to debug or use the Flash-> Erase option in Keil.What can be done to mass erase?I am encountering an error which tells unable to halt ARM core. Device = ADuC7026 Info: Device...
View ArticleRe: How to do a mass erase in boards other than the evaluation boards?
I'm unable to use the Flash---> erase option.Error comes saying " Cannot stop ARM device" The following shows the error message: Device = ADuC7026Info: Device "ADUC7026X62" selected (62 KB flash, 8...
View ArticleRe: Use of I2CxCCNT register in ADuC7xxx
The ADuC7020 I2C when configured for Master mode does not have an automatic way of generating a repeated start.The sequence you highlight above is the only workaround possible to try and generate a...
View ArticleRe: Re: How to do a mass erase in boards other than the evaluation boards?
You reported the same issue 2 months ago " Cannot stop ARM device" Did you fix it that time? If you did something to the part to lock it up, i.e. change to a non existing lock, you can only then mass...
View ArticleRe: Use of I2CxCCNT register in ADuC7xxx
Thank you..So I guess you need to make use of the I2C0CCNT register only when we need a repeated start.Is it?Will need more help when I further explore I2C. Thanks a lot for now.
View ArticleRe: WATCHDOG ADAU1761
Hi Wilfrido, So if I understand, the DSP by itself reset the watchdog counter. The only thing I need to do is to check the Error register . Is it corerct?
View ArticleRe: Re: How to do a mass erase in boards other than the evaluation boards?
2 months ago I had trouble with ADuC7020 evaluation board. Evaluation board showed the same error, which I could solve based on your replies to use RS2332 cable along with ARMWSD. This is for a...
View ArticleRe: SigmaStudio algorithm: can any latency introduced?
Hi, Generally the largest latency in a DSP system is the A-D and D-A converters. For example, a ADAU1701's analog in-out latency is typically about 1mS at 48KHz. This results from the...
View ArticleGNU Radio IIO blocks
Hi, I've installed GNU Radio on a Zynq 706 board and am trying to add the IIO block FMComms2 (from gr-iio at analogdevicesinc/gnuradio · GitHub) to it so that it can talk to an AD-FMCOMMS3-EBZ board,...
View ArticleClik here to view.
Extensive Control for AD9912 Eval Board without PC
Hi, I am willing to control AD9912 eval. board setting to generate specific frequency with Arduino or Rasperry Pi or else. But I have no experience to control such electronics. I haven't seen similar...
View ArticleRe: ADV7842 and registers “SPA_PORT_A”, “PORT_A_CHECKSUM”
Hi Alexander, I'm looking at the software driver source code and I can see that ADV7842 repeater map 0x72/0x73 and 0x7B are used for port A. I believe you are using the source code files downloaded...
View ArticleRe: ADV7842 and registers “SPA_PORT_A”, “PORT_A_CHECKSUM”
Hi, Matt Yes, I load library from: “http://www.analog.com/static/imported-files/software_modules/ADV7842_API_Library.exe”. That is You think, that whole division “8.9 STRUCTURE OF INTERNAL E-EDID FOR...
View ArticleSwitch to reset charge integrator
Hello I am designing an integrator to integrate output of the current sensor to obtain information on charge. I first buffered signal using an ADA4817 and use output of that amp to drive charge...
View ArticleRe: AD9257 Expected VIN Load
Hello Mr. Foote, The 100Ω terminations for the clocks are to comply with the requirements of the respective signaling standards (e.g. for LVDS, etc.). The analog input pins of the AD9257 are...
View Articleodd ad9361 noos/linux behavior at < 8.215 Msps
Hello, I am using an fmcomms3 + zedboard. I am attempting to run the ad9361 at a lower sample rate e.g. < 10 Mhz. Using the sd card shipped with the fmcomms3 (using AD provided fpga + linux drivers...
View ArticleRe: Re: port uboot on custom board based on bf548-ezkit(new bee)
Hi Aaronwu, Thanks for your helpful suggestions.Finally I successfully port my uboot on the custom board .Correct board file is attached (at least for me). thanks!
View ArticleRe: Re: Re: HDMI configuration(ADV7511)
Hi GuenterL, As per your reply, I have changed 7511 I2C main Regiser 0x15[3:0] = 0, Display colour is now chenged but its not clear. Three snapshots are attached for your concern. Note: 16 bit...
View ArticleRe: AD 9246 Evaluation Board HSC-ADC-EVALB-DCZ
Hello, Can you attach the FFT spectrum for the same input and clock signal? the distortion in the input is probably some impedance matching issue. Make sure the Waveform generator's output matches the...
View ArticleADV7611BSWZ-P and ADV7611BSWZ-P-RL
Hi, In the datasheet of ADV7611 (Page-14) , ADV7611BSWZ-P part is mentioned as a non-HDCP version. However, ADV7611BSWZ-P-RL part is not mentioned as a non-HDCP version. Can you please confirm if...
View Article