Clik here to view.
ADAU1452 Master Control Port
Hi there. I want to boot a codec (AD1939) over the master SPI port of the ADAU1452. When trying to drag, drop and configure the 'Master Control Port I/O' block in Sigma Studio (3.10.4 or 3.11 beta) I...
View ArticleStreaming tx with AD9364
Hi, We wish to stream some data out of the fmcomms4/AD9364 board. Luckily, we found that there is a piece of sample code Re: AD9361 Streaming Transmit. We disabled the cyclic bit, downloaded the...
View ArticleRe: Auto Sleep Mode in ADXL313
Hi Tao, I did not have ADXL313 in hand to double confirm your condition. But I have tried other similar part ADXL362, below is the test result.1. DATA_READY interrupt can be generated in sleep mode. Of...
View ArticleRe: problem with ADXL345 outputs
Hi, 1. Please try to make sure you can read DEVID (register 0x00) correctly.2. Try to write a R/W register and read back to make sure there is no probelm on writing/reading the register.3. When you...
View ArticleClik here to view.
Can't selfboot with EVAL-ADAU144XEBZ board
Hello, We bought a evaluation board(EVAL ADAU144XEBZ REV C). We had some issue on selfboot function. Please help to find what's wrong with our action. STEP 1: We build a project in SigmaStudio as the...
View ArticleAD9361 VCO calibration lock
HI guys. I work with on AD9361(FMCOMMS2) with my XILINX-V6 board.I make it work on FDD mode and the REF_CLK is 40MHz, and the working frequency is 2.45GHz. I follow the instructions of the...
View ArticleSEC Self-nesting on BF-70x
Hi, I have a question about SEC(System Event Controller) self-nesting interrupt. For instance two timers (timer0 and timer1) are set in SEC interrupt source (SEC Priority : timer0 > timer1). When...
View ArticleGP Timer EXTCLK mode on BF70x
Hi, I have a question about GP Timer EXTCLK ( clock source: SCLK) on BF70x. I want to start free run timer counter on BF70x Ezkit, but the timer never count up SCLK clock. My source code is below. void...
View ArticleRe: Porting of AD9361 to Altera FPGA
Hello Robin, Charly & the rest of the team Was there any progress with the porting of the HDL to Altera?We have some customers who are looking for this. BR,Alon
View ArticleProblem installing EVAL-ADISZ / 16210 with IMU evaluation software
Hello, I have followed the instruction on the wiki regarding the installation of this board but the board is not seen by the system. The Led L2 is only blinking very weakly (it goes on an immediately...
View ArticleClik here to view.
Re: ADF4159 - Example of a staircase waveform
hi rbrennan,I am using ADF4158 eval board now,I am just a learner and I want to know how to generate a ramp FSK waveform,how do i set Analog Devices ADF4158/4159 PLL Software.Can you help me?Thank you
View ArticleRe: Queries on AD9914 Parallel and Direct Mode
hi, i doubt why u said 0x06 is 0x00 instead of 0xC0?is ur way MSB or LSB?
View ArticleRe: FMComms 2 Sink GNU Radio block
Thanks for your help - I'm not quite sure what you mean by check the names of the channels though, I can't find any way of doing this on the analog devices wiki?The kernel I'm using was alread on the...
View ArticleRe: no audio output from ADV7626's Txa port
Hi Poornima, Mode: RXB->TXA/TXB (Splitter mode) HDMI Source: Blue Ray DVD Player SAMSUNG E5300 HDMI Sink: LCD TV SONY KDL-32CX520/SKYWORTH 39E780U L F/W: X2.2.1Exp5 Below relevant log file is for...
View ArticleRe: FMComms 2 Sink GNU Radio block
I've found a config file for the IIO Oscilloscope application which was pre-installed and does work for both transmit and receive which does refer to out_altvoltageX so I assume that this is the...
View ArticleADV7611 detect i/p mode
I want to know the input HDMI is interlaced or progressive, and I read the HDMI register HDMI_INTERLACED(0x0B),it always shows 0 which mean progressive input,I'm sure the input signal is 1080i.My...
View ArticleUART and lwip
Hi ADI's experts,I've a little problem. I'm not able to use UART if I initialize lwip. If I comment the adi_lwip_init function all work fine.I'm using BF609-ez board
View ArticleClik here to view.
Re: EVAL-AD2S1210 + EVAL CED1Z : no Excitation Signal
Hi John, When I'm entering "40" in the EXCITATION FREQUENCY here is what i can observe : (D7/D6)(D5-D4)(D3-D2)(D1-D0) -Blue signal is the CS (Test Point of the Eval-A2DS1210 board)-Yellow signal is...
View ArticleFFT Accelerator
Hi , In the Manual it is described that FFT accelerator implements radix-2 complex floating-point FFT butterfly . Which FFT function is similar to that of that FFT accelerator. There are CFFT ,...
View Articleadfmcomms1 square wave and adc
Hello all,Few questions regarding AD-FMCOMMS1 on KC705 no-OS 1) How do i generate a square wave through dma? I am feeding the LUT values as follows: const uint16_t sine_lut_i[32] = {...
View Article