Re: ADV7281 I2C config
Hello, I've asked an expert on this part to come comment. Most likely you have a very basic hardware problem. Dave
View ArticleRe: High Side Current Sensing or Differantial Amplifier Vs Difference Amplifier
See: http://www.analog.com/library/analogdialogue/archives/42-01/high_side_current_sensing.html Harry
View ArticleRe: EVAL-ADIS C/C++ Driver or Source Code Libraries
I just wanted to check back in on this. Look forward to hearing how this works for you. Best,NevadaMark
View ArticleRe: choosing ADXL346 interrupt ??
Hiaccording to the datasheet SINGLE_TAP bit is set when a single acceleration event that is greater than the value in the THRESH_TAP register (Address 0x1D) occurs for less time than is specified in...
View ArticleRe: IRQ0 Interrupt issue - ADSP21489
Hithe issue solved - i miss the nop needed because of the cache freeze.Page 4-88 sharc processor programming reference Itamar
View ArticleRe: SPDIF ADAU1445/6
SPDIF out sends only two channel, for rest channel You must use external circuit like WM8804, DIT4096 connected to serial out interface of ADAU.
View ArticleADSP-21369 FLAG3 as interrupt
Hi, As the title says, I'm trying to define the FLAG3 pin as an interrupt, but I don't see how. In the schematic files of the EZ-KIT Lite it says that this pin is IRQ3, but in the hardware reference...
View ArticleRe: AD5342, question on reference input
Hi Miguel, Please let me ask you to clarify again. When you talked as follows, > Vdd is not powered but probably connected to a supply so.. two things may happen,> 1- the supply is at high...
View ArticleClik here to view.
Re: How to communicate with ADE7754 to make an energy meter with PIC18F2520
this is the schematic...... i am using 15 watt bulb and 40 watt bulb........my project is to show the energy change on adding or rmoval of lamp load in running load....but in running condition...device...
View ArticleRe: Can the electro-magnetic field affect the IMU operation?
Hi Mark, Attached is the data gathered. The data is analized as 1. X-axis directs forward and Z-axis directs upward.2. Throttle is increased from 40% to 70% at 280 sec.3. Battery voltage supplied to...
View ArticleRe: USB problem on BF609 ezkit
Hi Aaronwu, Thank you for your reply.I have followed the steps described in this FAQ, but the problem persist. Is there a specific HW configuration to have in board?
View ArticleRe: Output Short Circuit Protection of AD5410
Hi Agni, I do not have much information to offer you on the topic of thermal interface material. However, our package expert has advised that he would not have any specific concerns with the use of...
View ArticleRe: ADF4156 Design Issue at 1911.642 MHz
Hello Kyle,See attached a pll file ( using ADIsimPLL_V3_60_06) ...can you supply me with your required channel spacing mad VCO details and I can modify this .pll file... note: you can doenload the...
View ArticleRe: ADSP-BF609 DEBUG error --Failed to connect to Processor
Hi Beck, Are you trying to connect to a BF609 EZ-Kit or a custom board that uses this processor? If you're using a custom board, please confirm it complies with our JTAG Emulation Technical Reference...
View ArticleRe: ADC_Capture function
Hi Satwik, The problem is, that when you try to verify the data after the second adc_capture, the cpu will give you a cached value, instead of the value from the specified memory space.Try to...
View ArticleRe: AD5933 + AD8606 Nonlinearity problem
Hi Miguel, Can you be kind to discuss about calibration procedure. According to AN-1252, Rfb and Rcal should be defined by equations Rcal=0.33*(Zmin+Zmax) and Rfb=(approx.)=2.3*Zmin/3 because my...
View ArticleRe: Color space of HDMI vedio of ADV7623
HDMI_COLORSPACE is decodes from the AVI Info Frame. If the AVI Info Frame shows all '0's then there is no info frame. 1) Do other sources have the same problem? 2) What model DVD player do you have?...
View ArticleRe: ADV7513:Register setting file
The input clock does not have an input clock jitter specification. As long as you meet the timing requirements you should be fine.
View ArticleRe: EVB-ad7781
Hi, I glad to say that the AD7781EVB works with windows 7.in the user guide ( and the EVB software ) its mentioned to remove LK1 to LK4,doing that disconnect the load cell from the excitation voltage....
View ArticleRe: choosing ADXL346 interrupt ??
Hi Yossi, Here is the case, If you use activity interrupt, when there is one sample over the 12g threshold, the activity interrupt will be triggered, it cannot wait for 300 ms. If you use single_tap...
View Article