Re: Difference between 2018 and SSM SSM 2018PZ
Meanwhile, thanks for the risposta.Devo replace ssm2018 without ending themes with a ssm 2018PZ there are differences? thank you very much
View ArticleRe: No HDMI output in latest Ubuntu design for ZedBoard
Same problem. - I checkout latest HDL libraries and project scripts from https://github.com/analogdevicesinc/hdl- Built HDL libraries and ADV7511 for ZedBoard using Vivado 2014.1 - I just needed to...
View ArticleRe: CN0274 Evaluation Board
Hello - Thanks for the quick response. I've been doing a bit more research and I really like the solution provided in this thread:http://ez.analog.com/message/40001 Using the PIC10F322 is really...
View ArticleRe: AD8352 DIFFERENTIAL AMPLIFIER
Thank you for ur valuable information....... Am applying the input clock with upto 50MHz, What would i do to make this circuit working for my input requirement.....
View ArticleRe: AD8352 DIFFERENTIAL AMPLIFIER
thank u umesh....... what would i do to make this circuit working for clock input with upto 50MHz, without introducing DC offset at the o/p.........
View ArticleRe: AD9254 EVAL
Dear Tony, Thanks for your response.We have already shipped these boards to customer.The issue currently is that the software is not showing up AD9254 as an option to select. Customer has tried to read...
View ArticleRe: Question: SPORT, TDM and DMA
Hi Yli, No need to use two ISR's. Because the FS and the clock are locked (and probably routed to the same pins as in my situation) the data is received in both sports, even if just one is signaling...
View ArticleRe: ADV7480 HDMI/MHL receiver
All the registers defined in the global structures"kaAdv748xRecHDMIPllInitTable","kaAdv748xRecHDMIEqInitTable","kaAdv748xRecHDMIMiscInitTable","kaAdv748xRecMHLEqInitTable"...
View ArticleRe: AD9361_Initialization
Hi Timo, ZC702 doesn't have HPC connectors: it has just two LPC connectors. However, it could be enough for your requirements. I'm not familiar with the LPC problems, so someone else will give you more...
View Articleseveral questions about STDI
adv7842 or adv7441a How to calculate BL?where can I find the detail parameter about different video format(RGB and HDMI) SVGA@60hz(800*600@60hz),according to 《VESA and Industry Standards and...
View ArticleRe: bf516 network sometimes become very slow
Use network to send recording data to PC.When network is slower lead to loss packet. Use iperf to test network capability, The network speed is very slower. somtimes about 1Mbit/s.
View ArticleRe: ADXL345 dev board firmware upgrade error
To be more clear, the button named PROG on ADXL345 DB board is the SERIAL DOWNLOAD, the button named RESET on ADXL345 DB board is the RESET button. Attached the user guide of the ADXL345 DB board. BRNeil
View ArticleRe: Poor SNR of ADV7180 and ADV7391?
Hi,Thanks at first.The video source is the standard color bar.The measurement equipment is Tektronix VM700.I will report the result which you talk about. Cheston.
View ArticleRe: ADXL345 eval board sample rate
Hi Hithesh, The sample rate depending in the .hex that you download to the MCU. The different .hex file can be found from the link below:...
View ArticleRe: ADXL362 400Hz data output
Hi Barry, What you say is make sense to me. Please check clock frequency deviation of ADXL362, on page 12 of ADXL362 datasheet, figure 29. You can find that the ADXL362 internal clock frequency...
View ArticleRe: AD5933 + AD8606 Nonlinearity problem
Hi, How are you doing the calibration?May you explain all the steps involve in your measurement? Regards,Miguel
View ArticleRe: AD5933 + AD8606 Nonlinearity problem
Calibration is done only with pure resistance (0.1%, +/- 25 ppm).The first step is estimation of unknown impedance.1. Rfb=Rcalib=10 k2. Repeat frequency command, Rfb=10k, Runk calculation (the first...
View ArticleClik here to view.
Re: ADV7125 & AD724
Hi, I have attached, the schematics pictures and one of the output. The output picture is a full screen. Only is brightness one part for the camera used. Regards. Thanks.
View ArticleRe: ADE7880 - Energy measurement
Hello Hmani, You are absolutely right! there were some communication problems between me and my collegue because both convinced we were talking about the same chip. Anyway now that is a solved...
View ArticleSPDIF to I2S Convertion without uC interaction
Hello, I am looking for a part that will accept SPDIF upto 192kHz and convert it to 24bit I2S. I need this part to be completely HW configurable (pull up/down resistors), no I2C no SPI no other...
View Article