Re: Adxl345 linux driver freezes, [raspberry pi i2c]
I built this driver into kernel so i don't have to load it anymore. I'll try clean installation and clean kernel repository to make sure that everything is done properly.
View ArticleRe: AD-FMCOMMS3-EBZ and ZC702 ethernet problems
Hi, I'm still not able to reproduce it, can you send me the exact dtb files you are using? Thanks,- Lars
View ArticleADZS-BF561-EZ lIte kit hardware problem....Plz help
Dear Members, I have purchased ADZS-BF561-EZLITE from Digi Key. The kit was getting heated from start. After 2 days when I was trying to connect it to PC for creating session. I am getting error...
View ArticleRe: ADSP-BF561 Eval kit downloading error
Hi David,These error comes ,when i try to connect to target...i.e create a sessionI am using the on board debug agent.yes i have downloaded code to this kit before and it was running properly.I am...
View ArticleRe: ADZS-BF561-EZ lIte kit hardware problem....Plz help
Hi Shivam, My colleague just answered a very similar question over on this thread (possibly from someone else at your company, I believe). Could I ask you to take a look at his inputs on that thread,...
View ArticleExternal clock signal changes the ADC read values
I have a circuit with four AD7190s. We read at 24bit accuracy as frequently as the chips allows. Each set of four reads must be absolutely synchronized. We read at full resolution (24bit) from AIN3 and...
View ArticleRe: ADSP-BF561 Eval kit downloading error
Hi Asmi, Thank you for the clarifications. In the past we've seen target connection errors caused by the processor booting a corrupt image from flash. To make sure this isn't the case here, I would...
View ArticleRe: How do you synchronize conversions from 2 AD7799 converters
The AD7190 has a SYNC pin designed to allow you to get this level of synchronization. I know you prefer not to change what you already have and with that in mind your approach is worth a try. As you...
View ArticleVPP & CSI MAP Device address
I have referred to the adv7180 SD video decoder linux driver software available in Analog Devices https://github.com/analogdevicesinc/linux/blob/adv7280/drivers/media/i2c/adv7180.c In this code I found...
View ArticleAD8606 inductive load - nonlinearity problem
Hello, I am using AD8606 in system with AD5933 for complex impedance measurement. I have posted this issue on DDS section but after discussion they told me to post here. here is my previous...
View ArticleRe: ADAU1701 DAC output filter if using differential-input amps?
Hi Coleman, True, I forgot the other resistor! I'll use this filter. The Fs of the project is 192KHz, so I think it will be a good filter. Thank you so much for your help. Best regards,Marti
View ArticleAD7190 evaluation board
Hi there,I tried installing AD9970 evaluation baord.But after the instralltion, PC does not identfy the eva-baord via USB.Looks like it has something to do with USB deriver soft.Please tell me how to...
View ArticleRe: How to validate MIPI data transmitted by ADV7281-M?
Hi, If your MIPI receiver provides no aids for validating the incoming MIPI signal I'm afraid there is not much else you can do. The ADV7281 supports sending out a testpattern which can be enabled via...
View ArticleOffset voltage sign
Are there any OpAmps with defined sign of the offset voltage?Tank youPhil
View Articleoffset voltage sign
Are there any OpAmps with defined sign of the offset voltage?Thank youPhil
View ArticleRe: CN0326: Isolated Low Power pH Monitor with Temperature Compensation
Dear Sir, I am working with "EVAL-CN0326-PMDZ REV.A" evaluation board for pH measuring application. While searching for CN0326 Evaluation LabWIEW Software, i found that there are three different...
View ArticleRe: adau1761 on ZedBoard(no linaro)
Hi,I meet the same problem, how to solve it? Which u-boot I should use?
View ArticleRe: CRC on 1446
Thanks Wilfrido, i noticed also that many DSP registers got undefined, as reported by the host mcu compiler, when i turn on the CRC check so i use the newly generated *.h files.If you want, i can be...
View ArticleRe: CN0326: Isolated Low Power pH Monitor with Temperature Compensation
H Prabhu.S, Thank you for having an interest with CN0326 Evla Board.you should use the latest version 2.0.0 found for your study.the source code for CN0326 Evaluation Software will be sent over to...
View Article