Clik here to view.
Re: low cost hart sensors (AD5700)
Hi,We can only provide support on the AD5700 modem itself. For support on other specific HART registered components, please visit the HART foundation website. That said, what you could consider is a...
View ArticleRe: ad9361
Which evaluation platform are you using? If it is an AD-FMCOMMS platform then you can find the information on corresponding wiki page. AD-FMCOMMS2 provided as an example. AD-FMCOMMS2-EBZ User Guide...
View ArticleClik here to view.
Re: Data Transmission with AD9361 on Linux-OS
HI, rgetzIf i consume data faster that it was produced, (by sending them to /dev/null), my "iio_buffer_refill" will re-read some data, or it exist a mechanism that does not allow that?Thx in advance
View ArticleRe: Accurate phase detection at ~10MHz
The AD8302 is the one you want. The AD8333 was designed for phase alignment between n-channels but the AD8302 actually performs phase measurements. The apps engineer is Joel.Dobler@analog.comBest
View ArticleClik here to view.
Re: How to communicate with ADE7754 to make an energy meter with PIC18F2520
Hi MARS Thanks for sharing your schematic! But I still do not see how you have connected the voltage and current inputs to the ADE7754IC. Please look at the below picture for a typical 4-wire wye...
View ArticleRe: ADV7401: ghosting video output from CP with 480p input.
Just to confirm, we are talking about the analog input side, correct? This board was not laid out with the video input as the top priority, but there might be somethings we can do to improve the...
View ArticleRe: ADRF6801 eval
No. The closest thing we have is an Evaluation Board Test Procedure that we use to quickly test the evaluation board's functionality. Do you think this might help?
View ArticleRe: ADV7401: ghosting video output from CP with 480p input.
Yes, analog traces can cause this problem. If you can attached the schematic and layout here I'll take a look at them. Let me know if you want to take this off line to be more confidential. A lot...
View ArticleADE7878 - DVDD error
Hi, We are using an ADE 7878 development board and a 3.3V Arduino to communicate with it using SPI. We were communicating with it successfully for a period of time but it has now stopped communicating...
View ArticleRe: SPI Transmit in slave mode
This is indeed pretty odd.Here's what I would experiment with:Try introducing short pauses between the words being pulled by the ARM (and possibly remove the SMLS bit).What is the slave select line...
View ArticleRe: Using AD584JNZ as a 5.0V Reference
Hi Anna, I also simulated in Multisim. It makes a big difference when you connect pin 4 to ground.That was my problem, I simply forgot to connect the ground pin. Thank you, David
View ArticleRe: BOM for the AD9625 Eval board and Eval board question
Hi Belenie, You are exactly right on pin 6 of U802 being DNC. The grounded pin was carried over from another schematic. I probably need to add a note to the schematic. I will send you the BOM in a...
View ArticleClik here to view.
Re: How to configure display timing via EDID
Hi GuenterL, I am using two Notebooks to test the EDID. One has a Nvidia ION and the other an Intel HD 4400 graphic. After removing all user defined resolutions I created earlier, both systems use a...
View ArticleRe: EVAL-ADV8005-SMZ Question on enabling JT6 Header
If you program your EVAL-ADV8005-SMZ with the application binary BF_7842_8005_VSP_1.80_RC3_20140321.bin shown on the following page:Advantiv™ EVAL-ADV8005-SMZ-P Video Evaluation Boardit will route the...
View ArticleRe: AD9106: a bunch of questions.
Hi Korbinian - Is this answered as far as you're concerned? Is there anything else you require? Thanks,Larry
View Articlehelp choosing and configuring clock source for AD9102
Hi everyone, I'm choosing and configuring the external clock source for an AD9102, and I'm having some trouble interpreting the datasheet. I have two questions: 1. How should CLDO and CLKVDD be wired...
View ArticleClik here to view.
Re: ADF4350/1 & ADCLK846
Hi Alon, Do you need LVDS outputs? Typically ADCs benefit from the large swing and fast slew rate of an LVPECL driver.This circuit note shows an ADF4351 connected to the ADCLK948 and the resulting...
View ArticleRe: code for AD7193 spi
I'm also trying to use the arduino to communicate/control the AD7193. Basically I just want to use it to read voltages and set the PGA to 8. Is there an example code of how to do this? Also is the...
View ArticleRe: Using HMC951LP4
Should be fine as long as you keep LO and RF drive levels well below absolute max ratings. Typ LO drive of 0dBm should not damage part when biased off. RF to IF isolation should improve when biased...
View Article