Clik here to view.
Re: image processing demo for BF527 in Blackfin Processors
Hi, Thanks for Quick reply.Where Most of Software module file contain Board rev2.2.But i have ver 2.0 BF527 along original CCES and VDSP++. I want to run Blackfin...
View ArticleRe: Sine wave in No-os driver FMcomms1-ebz
DragosB, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is...
View Articlebf609 running frame capture example
Hi,I was trying to run the frame capture example for bf609 ez kit and video decoder EI3. I get the following messages in the console. UYVY422 video, Capture frame to fileDecoder Soft Config -...
View ArticleClik here to view.
Re: ADV7403 power supply
I have used 10uF, 6.3V Rated capacitor to CAPC2 and CAPY1 pin, in my design. Whether it cause any issue?I have powered-On the board. I did not find any capacitor damage / fumes on the PCB. Please...
View ArticleRe: ADV7403 power sequencing
Thank you for the recommendation regarding power - on sequence. In my design I have provide 3.3V, 1.8V Analog and Digital Power Supply Simultaneously. In the datasheet, or reference manual I did not...
View ArticleEmulator ICE-100B error
Hi,I am using a customized board based on the BF-538F. I am trying to emulate the using the ICE-100B emulator but I am getting the following errorError: 0x80048015Error Description: Open Device Driver...
View ArticleClik here to view.
ADV 7403 Video Decoder Power Consumption
Hi, I am using ADV 7403 Video Decoder in my design to convert the YC(luma and chroma) Analog Input signal to Digital signal in BT .656 standard. I have powered-on my system. I have found few...
View ArticleCustom design in Zed board, FMCOMMS-EBZ, Reference design
Hi, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is there?...
View ArticleA suitable interface device for AD7762 or AD7763 VOH
HiI would like to select the suitable interface device, as level translator to 3.3V, for AD7762.An interface device's Vinh min is mostly 0.7 or 0.65 X Vdd min, I think.It is about 1.65V at vdd=2.5V.But...
View ArticleRe: IIR filter crashes on the fly
Hi Dan, Did you get your -1701 to safeload your filter coefficients? Bob
View ArticleClik here to view.
Re: ADV7619 pink lines after switching from unsupported to supported resolution
Thanks for your quick response, will try your suggestion.
View ArticleADAU1761 I2C only works after programming device
I've done a bunch of work with my ADAU1761 board and now I'm ready to have my microcontroller program it. I've read the presentation/guide on how to do it from analog. My codec programs fine when I...
View Article5.23 conversion sample code
Is there sample code for the conversion of 5.23 to the hex value(s) I have to write over I2C for my ADAU1761? I'm just getting into trying to program it from my PIC32 and I'm not really sure where to...
View Article5.23 Convert to Hex for I2C program of ADAU1761
Is there sample code for the conversion of 5.23 to the hex value(s) I have to write over I2C for my ADAU1761? I'm just getting into trying to program it from my PIC32 and I'm not really sure where to...
View ArticleClik here to view.
ADAU1761_ About SigmaStudio
I have been tested using the EVAL-ADAU1761Z and ADUSB2Z. 1, I've saved the SigmaStudio project using the "Save as ..." . However, change information of Automatic Startup will not be saved as shown...
View ArticleRe: SXGA @30fps support on ADV7612
Hi GuenterL, Thanks for the info. Then does the same apply for ADV7513 transmitter as well. Can I give it SXGA30 and it will transmit it out? This question arises as I have ADV7612 in my design as...
View ArticleRe: ADM3251E DCDC enable/disable
Hi MMA,Thanks for your reply.Let me make sure if my understanding correct. Internal Power Enabled : 4.5 to 5.5VInternal Power Enabled : 3.7 to 4.5V Internal Power Diabled : 3.7 to 3.0VAs of 3.7V to...
View ArticleClik here to view.
AD7265 Fully differential Configuration help
Hi I would like to use AD7265 in fully diff configuration for data acquisition system.I confused on the Differential input range mentioned on the datasheet. My requirements are VDD: 5V...
View ArticleRe: AD7476 behaves like reference is only VDD/2.
Hi Dneise, According to the datasheet specs, LSB is equal to VDD/4096, so you are right that it should be around 1.22mV. There are 2 possible elements that you can look into: First, what did you use...
View ArticleRe: Issues with EVAL-AD7294-2SDZ Current Sensor
Hi, Arne. Do I understand that you installed the same Rsense for both evaluation boards? Can you send an illustration for both of your setup including the modifications you have applied? Please also...
View Article