Re: zedboard fcomms1-ebz interfacing
helloI am following the discussion..I am working on zedboard with ad-fmcomms1-ebz..My need is to transmit digital data from zedboard through fmc to ad-fmcomms1-ebz and receive the transmitted digital...
View ArticleRe: Changing the Reference Design for the AD-FMCOMMS1-EBZ
hello..I am following the discussion..I too had a same doubt of transmitting signals to DAC of ad-fmcomms1-ebz..Can u help me on how to create a core that generates 8 samples at a time (4 for I and 4...
View ArticleRe: AD8554 - Gain Bandwidth Product doesn't depend on Gain
Hey, thanks a lot for your time! I was stuck with this for quite a while. Problem was, that the noise gain is rarely mentioned anywhere if you do not look for it in particular. So again, thanks a lot...
View ArticleHow to calculate the coefficient of "bass boost" module in ADAU1701?
Hi everyone, I'm using ADAU1701 and would like to control it with the MCU as the host.As I am going to use "bass boost" in my schematic,but I can not figure out the formula to calculate all the...
View ArticleRe: ADV7610 I2C answers xFF for every registers read
Finally had some time to work on this problem and discovered that the SCL and SDA lines were not that nice after all. On the scope, it looks good in zoom out to interpret the I2C message, but in zoom...
View ArticleADAS1000 ECG chip and use of bypass capacitors
The ADAS1000 ECG Front End data sheet suggests using .01uF bypass caps on the analog and digital input supply pins (page 78) but the reference design EVAL-ADAS1000SDZ User Guide schematic shows the...
View ArticleADV212 EIRQFLG doesn't reset
Hello! I'm trying to use ADV21, I make all according to fig.12, page 17 of Programming guide. I have read correct firmware ID=0xff82. Then I try to reset IRQ flags by writing to direct address 0x6...
View ArticleClik here to view.
Re: DVI to VGA active RAMDAC using ADV7123
how would i investigate the right part? like i said i dont really know much about designing hardware stuff, so i dont know much about FPGAs or how to program them, i only know software programming (C,...
View ArticleRe: accelerometer for induction motor vibration
Great information, Neil! The following article might be useful as well:http://www.analog.com/library/analogdialogue/archives/48-06/vibration_monitoring.html
View ArticleRe: ADIS16251 Screw Torque and Bias
In general, MEMS gyroscope's bias is sensitive to change in its package stress profile, which can happen through tightening the screws down on the PCB. So, this is not a large surprise.
View ArticleRe: ADV7611 EDID configuration
Thank you for the support. This is strange since the original file was according to the script provided by Analog Devices.Is there any change in the DTD between the original file and the new one. We...
View ArticleUsing no OS driver with custom h/w in verilog
Dear Support Engineer, I am having AD-FMCOMMS1-EBZ with ML 605 board. I have run No-OS driver successfully and able to run its API.I have my custom block of OFDM written in verilog. I want to interface...
View ArticleADN4605 NRZ and PAM data support
Dear SupporterFrom the ADN4605& ADN4604 DS, it looks that it supports only NRZ data. Will it support PAM data?ThanksFreddy
View ArticleAD8177 AD8175 design support files
Dear supporterAre there design support files for the AD8177/5?If not, what is available to help my customers?Eval board documentation, Schematics? SW? Scripts etc.Nothing of the above is found in ADI's...
View ArticleRe: Auto detect input
Hi Chris, I have been crazy busy so only now had time to look at this to convert to a mono input. Im a little confused how to deal with the and gate and nand gate any help would be greatly appreciated...
View ArticleClik here to view.
Re: Simulink ZC702 AD9364 fmcomms4-ebz
Hi Andrei, I recently realized that Windows SDK was not installed when I checked the log file. I managed to install Windows SDK by first removing microsoft visual c++ 2010 redistributable. I am now...
View ArticleRe: SRC AD1895, how much difference between input and output sample rate does...
Thanks for your reply.I will wait your answer. When you get the datal information, please let me know.
View ArticleRe: SPDIF Enable register of ADV7511W.
Hello, Thank you for your reply.Could you tell me the status of these questions? Best regards.
View Article