disable only anomaly 05000262
hi !I'm using a BF537 and currently generate code for siliconRev.0.2is there an option to disable only one (w_05000262) anomaly for the file or the project, becausein this case I use no cache mechanism...
View ArticleRe: AD7608 serial read trouble
Assuming worst case t18 = 30 ns (spec for Vdrive = 2.3 to 2.7 V, BTW mine is about 3.2 V but t18 spec for 2.7 to 3.3 V range is missing form the datasheet rev. A), and SCLK high/low are 40ns each. So,...
View ArticleRe: AD9361+Zedboard and AD9361_iiostream example
ok .. recap ...i can't use and test the ad9361_iostream source example on a target whit Petalinux ?I must use only Ubuntu linaro on the target board ?
View ArticleRe: Can the ADM1073/5 be modified for positive (+48V) hot swap application?
Hi Brent, Yes but only if you have only one current return path.the ADM1073 uses low side control scheme where it control the "return current" from the load.most of the -48V systems have an isolated...
View ArticleAD8054 Voltage Stabiliser application
Hi, I have a customer using the AD8054 in a voltage stabiliser application. It is configured as a voltage follower :- 0-5V on the +ve pin. -ve pin connected to the output. On the output he has two...
View ArticleRe: Zedboard + FMCOMMS1 + reference design problems
Dragos, I have built the binary again, I put screenshot of the window attached. The result was the same - the board didn't boot. For some reason, SDK through some warnings to the terminal: bootgen...
View ArticleAD9643 initialization problem
Hi Sir, I have a question for AD9643 initialization issue.When I power on the AD9643 and it will load the default value as Table 14?It means I don't use the SPI to initailize the AD9643 first time and...
View ArticleClik here to view.
Re: AD7746 full scale adjustment
Hi Ricky, the AD7746 full scale range is fixed to +/- 4pF per design and cannot be adjusted,however the device is 24-bit CDC and should allow you to achieve sufficient accuracy even if you use only +/-...
View ArticleRe: the Advanced Expert DAI can't work for Vsdsp++5.1.2
Hi, I have moved this from the Processors and DSP community to the SHARC Processors community, and will continue the discussion here. When you ran "regsvr32.exe ...", did you ensure you launched the...
View ArticleRe: Link register?(ADV7625)
Hello, Matt-san Sorry for my delay. I have confirmed that phenomenon on your evaluation board. 1. Run any script except MUX mode.2. Write any value(for example 0xAA) to Tx Test Map, 0xC4[7:0]3. Read Tx...
View ArticleRe: Does Loopback mean that the received data can be transmitted directly?
Yes this is version 6. -Michael
View ArticleTiming contraints not met for FMCOMMS2 project build on ZedBoard
Hello, I am trying to build the HDL reference design for the FMCOMMS2 board on a ZedBoard platform. I have successfully followed the instructions in ADI Reference Designs HDL User Guide [Analog Devices...
View ArticleLevel translation of ADG3308
We are considering to use a ADG3308.It is written Low cost serial interfaces is the target in the data sheet.Can ADG3308 translate level of I2C? If ADG3308 doesn't support I2C, please let me know the...
View ArticleAD9129 DC Coupled Output
Hi! I'm evaluating the AD9129 DAC and I was wondering if someone could suggest me a topology to have the output DC-Coupled. The datasheet gives AC Only output configurations. Ideally, I'd like to have...
View ArticleRe: Addressing more than four AD5242 over I2C
Thanks for your reply LucaV.I have decided on using the Mux controlled I2C line as discussed above.
View ArticleRe: AD7190 no constant values
Oh , Sorry i dont get the right values.i still get values about 0x6XXXXX or 0xFFXXXX
View ArticleClik here to view.
Re: ad9361_init : Unsupported PRODUCT_ID 0xFF
Hello Dragos, thanks for your fast answer!!!We are using : ZC702 + ADFMCOMS-EB2 Hardware is OK becasuse in the "boot" from the SD card the console mesages reppor all the test OK regarding the AD9361...
View ArticleSPDIF Enable register of ADV7511W.
Hello,I have questions about "SPDIF Enable" register of ADV7511W. Question 1:I had investigated the behavior of "SPDIF Enable" register (0x0B[7]) of ADV7511 by using ADV7612-ADV7511...
View ArticleRe: ADE7878 AVDD DVVD error
Hello,I removed the crystal and supplied CLKIN with a 16.384 Mhz square wave through a generator with peak 3.3V. I checked CLKOUT and it gives the inverse of the input signal as expected. But the Ref...
View Article