Re: Some questions about filter, rssi and hardware gain
ret = iio_device_attr_write_raw(tx, "filter_fir_config", filter_buf, filter_len); What is tx?Can you print your buf to console? Why are you trying to do direct register access?- if you are modifying...
View ArticleRe: libiio ad9361-iiostream example
Jie Yan schrieb: Hi Lop.ng, I am going to study the iiostream.c and try to modify it however I have no experience of C or C# programming in the environment of Ubuntu or Linux. Could you give me some...
View ArticleAD7195 AC Excitation using Eval Board soft
Dear SupportUsing the AD7195 EBZ eval board along with the supplied soft I'm not able to check the expect behavior of the AC excitation.I deliberately debalanced my bridge and I don'n see any...
View ArticleRe: Why use this method to set the hardwaregain cause error?
Does the default gain control mode of ad9361 is manual gain control?Thanks, Michael.
View ArticleADL5201 Common Mode Input Voltage
Hi, In table 1 of the ADL5201 data sheet it states that the input can be +/-10V p-p if the attentaution is set at -11.5db.Yet, in table 2 the absolute maximum VIN+ and VIN- specifications provided...
View ArticleRe: Does Loopback mean that the received data can be transmitted directly?
Dear Michael, Thank you for your professional experience . I have tried to use AD9361 to receive FM program.Unfortunately , the FM Broadcast program couldn't be demodulated by iio_fm_radio app which is...
View ArticleRe: cn-0209
Hi, What is the purpose of using 24 bit ADC in the circuit for cn-0209?Will a 16 bit ADC be sufficient? Regards,uaim
View ArticleClik here to view.
Re: Analog tools integration support
May I recommend that you start reading here: http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms1-ebz The FMCOMMS1 platform on Zed is already fully supported by our Zynq SD card image....
View ArticleRe: Does Loopback mean that the received data can be transmitted directly?
It's printed in your kernel start up messages.(type dmesg)Alternatively you can read HDL register 0x0. -Michael
View ArticleLDO for HMC624LP4 Attenuator
Which LDO is suitable for HMC 624LP4 attenuator. and what is the current value of VCC port of attenuator. Thanks
View ArticleRe: Can the AD5593 design to measure battery impedance?
Hey Miguel, thanks for the quick response. Can you provide some information material regarding the testes AFE?I would like to include AD5933 and the capability of it in a lecture at my university. Best...
View ArticleWhat's your recommended gyro sensor?
Dear Sir/Madam, Our customer is searching following gyro sensor.So what's your recommend device for this case? Sensing angle = +/-10 degreesResolution = 0.1 degreeapplication = robot arm, so need small...
View ArticleADV7611 XGA DVI support
Hello Friends, I am using ADV7611 to take input, XGA ( 1024 X768) @ 30fps as DVI Input. We want to configure the output as BT656, YCbCr 4:2:2, 8-bit interface in SDR format. The Back-end processor can...
View ArticleIs there a device that can recover an 80MHZ clock from a pulse train
Hello I have a 80Mhz pulse train with the following characteristics Pulse is approximately 3nS wide and 15mV in height, There is some DC noise of a simiiar frequency, up to 5mV I want to recover the...
View ArticleAD9856 Evaluation Software
Hi, Could you please help me to find or provide Evaluation Software for AD9856? I just lost CD with it. Thank you in advance. Regards,Ivan
View ArticleRe: Does Loopback mean that the received data can be transmitted directly?
Dear Michael, Thank a lot! Wish you all the best! -Jie 2014/10/14mhennerich
View ArticleRe: AD9361 with Filter enabled
What is the proper way to initialize the AD9361 with filter enabled?how to enable the filter?I have tried modifying the following values:phy->bypass_tx_fir = false;phy->bypass_rx_fir = false;but...
View ArticleClik here to view.
ADV8005 software driver
Hi, I have the EVAL-ADV8005-SMZ evaluation board. I currently use an USB-to-Serial adapter with putty terminal session to communicate with the board. I also have your software driver source code...
View ArticleRe: ADV8003/8005 OSD menu , start position&end position
Hi I'm sorry to tell you I have no the EVAL board of ADV8003 and ADV8005. But I 'm using the tool of Blimp of v3.5 But I don't know how can I config the position of the osd menu .
View ArticleADN8831 issue
Hello to all.We are making new design with ADN8831 and we have problem how to determinate R and C for PID In laboratory we connect to our system laboratory TEC driver THORLABS TED4015 – this device is...
View Article