Re: ADV7611: HDMI input signal is not detecting
Hello Guenter, Now my HDMI Rx and Tx loop back is working and able to receiving the video.Thanks for your support. And i am facing one more issue in HDMI Tx, when i disconnect and connect back HDMI Tx...
View ArticleRe: AD-FMCJESDADC1-EBZ reference design not working with ZC706?
Hi Rohan, Using your host PC, you have to copy the downloaded file (zynq_image_8gb_2013_12_12.img.xz) to your SD card. Depending on what OS you are using, you have to follow the corresponding steps...
View ArticleAD9517 SPI with AD9467FMC
I just found on wiki page of AD9467FMC that reference design is using default configuration by using external clock and AD9517 is still accessible via SPI. I checked the C code and everything should...
View ArticleRe: ADV7343 + TW8811
thank you for your replywe put table 82 with a little changes17 0200 FC01 0002 6080 1182 CB87 8088 108A 0C But the problem is that we dont get the correct V sync, that comes out of TW8811we get a...
View ArticleClik here to view.
Re: Smearing problem when use ADA4858-3 driving and equalizing a 100M VGA cable
hi, Jane. I simulated a part of your circuit and it turns out that your magnitude vs. frequency is way far compared to the figure 5 of your reference. I've noticed that the value of your RG is 56ohm...
View ArticleRe: About eva-boad UG-478
Hi Johnny, Sorry that I did not realized the section.I really appeciate your support. Best regards,Tarzan
View ArticleRe: ADE 7880 Accuracy Issue
Hi hmani, I would appreciate your help! I tried to give all calibration information in the message above. But step by step... PhaseResolution 306E-6d, freq: 50 Inductive case:UL1 = 110V, 60°IL1 = 1A,...
View ArticleRe: AD9517 SPI with AD9467FMC
Hi Rohit_Kumar, If you want to use the on-board AD9517, you have to make some modification on the board. Please check out this thread. You can ignore those lines on the C code, it's going to get an...
View ArticleRe: AD9835 FSYNC voltage level
Hi Aaron, Before do that, power the part at 3.3V and try to send the command directly without connect level shifter first.regards,Miguel
View ArticleRe: AD9835 FSYNC voltage level
Not a problem Miguel,This will save some time!Cheers,Aaron
View ArticleRe: AD9517 SPI with AD9467FMC
Hi Istvan, it is written that The osc can be enabled by doing the following:- P200 to enable the osc- remove R209 R210- place C205, C206 as 0ohm resistors- remove CR200 The performance of this...
View ArticleRe: Problems obtaining output on teh BF527 LCD for LCDColorBar example
Hi Ram, I'm pleased to hear that the LCDColorBar example is now working for you without any problems. Regarding the screenshot above, the Debug window is reporting Core 0 [Debug\LCDColorBar.dxe]...
View ArticleRe: FMCOMMS1 ACCESS TO AD9523 REGISTER
Did you try plugging in the HDMI monitor, and keyboard mouse? http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms1-ebz/quickstart/zynq Thanks-Robin
View ArticleRe: VDK accessing multiple SPI devices
Hi There Tim. Craig asked me to chime in on these SPI questions... Regarding the most recent question, your configuration is correct to enable the SPISSEL5 as a SPI signal, and it is the signal that...
View ArticleRe: AD9361 Fast AGC mode question??
"AGC Lock Level" is typically set to -10dBFS. You have to set the threshold levels correctly. The gain will be adjusted by AGC as close as possible to the AGC Lock Level. RSSI depends on the gain...
View ArticleRe: ADE 7880 Accuracy Issue
Hi Heimo The reason I ask for energy measurements is to understand why you think inductive case is erroneous. From above data, it is clear that the sign of the error changes when you switch from...
View ArticleLeakage on ADG732
I am using ADG732 as a de-mux on a couple of my projects. in an open socket condition, when I force current I notice a leakage on the input pins even though I should be hitting the programmed clamp. By...
View ArticleRe: Ultrafast Comparator for Sine wave at 16KHz
You can order the EVAL-ADCMP601BKSZ board on our website.http://www.analog.com/en/special-linear-functions/comparators/adcmp601/products/EVAL-ADCMP601/eb.html
View ArticleSchematic / Layout review
Someone asked by email: I would like to send someone at ADI a schematic/layout that includes AD9361 to review. Is there anyone who can do this? Thanks-Robin
View ArticleAD9361 I/Q
We need to build a system that, at its core, needs to be a MIMO transceiver: I/Q analog ports (eight ports) at a minimum 40MHz bandwidth on one side and RF ports (four ports: two TX and two RX) at...
View Article