Clik here to view.
Re: ADE 7880 no-load conditions
Hi Heimo1 Please find below an alternative procedure that will help you implement the no-load functionality using ADE7880 in a uniform way, even if the phases are entering no-load condition one-by-one....
View ArticleRe: unable to mount jffs2 file system in bf548
Thanks for the reply I tried to boot from the uImage... However i am getting the new error now as devtmpfs: error mounting -2, the kernel log is also attached below . If you have the uImage and working...
View ArticleRe: SSM3302
Hi BillREGEN is high (+5Vregulator ON) as in my case and I also run into this (or similar) problem. The AVDD supply pin is a very sensitive beast and need a capacitor 10nf..100nF. Place this capVERY...
View ArticleRe: UVLO min/max of ADuM5404
Hi BrianAh,,,,,Ok,I am still waiting for your answer.Thanks Kaos
View ArticleRe: How to calculate AD9858 DFTW and DFRRW ????
HiIn Sweep mode first we assigned CFR Address like 0x00 [7:0] 011010000x01 [15:8] 100000000x02 [23:16] 10000000 also Explain me about Load Delta Frequency Timer ????this bit be high or low in...
View ArticleRe: Eliminating the cable capaciance
Hi, Iam using it with the range extension circuit. Its supposed to measure the capacitance b/w exc and cin. But i guess there's some leakage to ground through cable capacitance. Is there some way to...
View ArticleADIsimADC in MATLAB2011
Hi, I'm trying to use ADIsimADC as the source of data for a research in my university. Using the VisualAnalog interface everything is fine, but seeing as I need data from many frequencies and...
View ArticleRe: ADV7182,ADV7340 and ADV7511 video decoder/encoder configuration
Hi , We are using ADV7511 for DVI Out , ADV7182 for CVBS Input and ADV7341 for CVBS output. ADV7511 working properly as per expected. ADV7182 register configuration is done as shown in the attached...
View ArticleUsing the ADAU1700/1701 DSP for Radio Communications
We are currently working on a multimode radio transceiver and one of the functions we wanted to add was DSP primarily for audio signal processing on SSB receive. This in reality is a low intensity...
View ArticleRe: ADXL362 datasheet questions
Hi, 1. You can find that in item 6, the part begins the measurement in wake-up mode, this means the ODR is around 6Hz, then 30 samples means 5 seconds.2. Half_BW does not impact ODR, it only impact...
View ArticleRe: The problem of excause 0x23?
Hi jobo23:Thank you very much. I'm very sorry. Now I am away on business . If I go back, I will reply you.
View ArticleValid solution to sync 2 RF PLL in multichip AD9361?
Will this idea below valid to provide a workarounfd to sync 2 RF PLL of 2 AD9361 devices? 1. Assuming that we have 2 X AD9361 devices. One of the 4 available Tx channel is transmitting at...
View ArticleRe: Exceed Input Common Mode Voltage
Hi Tino, I'm sorry for missing your last question. Would you mind letting me know what your circuit configurations are? We will be asking the designer so he can give some insight on what's happening...
View ArticleRe: ADL5350 Mixer
Hi, Georgy, Thank you very much for your reply.We understand what you mentioned.We would like to know the NF of Figure 59 circuit if you measured it. Best regards, Nikkee
View ArticleSchedule of CM40x BSDL Files
Hello, I' d like to know CM40x BSDL file release schedule. Is it a same timing a device production?Thank you for your help as always.Best regards,Sofy
View ArticleRe: unable to mount jffs2 file system in bf548
Thanks for the detailed information, to boot and mount the rootfs from a uImage, you should revert the kernel command line back in u-boot environment, it should be something like "init = /dev/mtdblock0".
View ArticleADV7611 TMDS PLL
Hi, Using ADV7611 in our closed system, TMDS PLL may not be able to lockwhen a random TMDS frequency signal from tens MHz to hundreds MHz is inputfor a few seconds then normal signal is input into...
View ArticleRe: The full scale of AD7687
Ryan_Curran wrote: To provide the correct impedance translation, which is the point of the amplifier, you will need to use a buffer per input leg. -- RyanI have schemata based AD7687 which didn't need...
View ArticleAudio Amplifier
I am searching for a good Audio Amplifier for my 2x 8 Ohm Speakers and i put the SSM2315 and SSM2375 Eval boards to be tested.Both of them werent loud enought for my application. The SSM2315 has a 6dB...
View Article