Re: Sometimes Eth0 can't recv data when BF609-board powers on
Eth0 in u-boot works OK, but errors may occur when ucLinux boots up. I boot the ucLinux from nor-flash. Or the error can be repeated just by "ifconfig eth0 down" and "ifconfig eth0 up" in ucLinux if...
View ArticleRe: Perform reset through JTAG
try if the bfin-gdb-proxy --reset will help, as documented in https://docs.blackfin.uclinux.org/doku.php?id=toolchain:debug:gdbproxy&s[]=gdb&s[]=proxy this will reset the processor.
View ArticleRe: Adv 7611 FMC Imageon Input Frame rate
Hi, It seems you have already got the answer: http://ez.analog.com/thread/36291 Regards,Dragos
View ArticleRe: exporting the reference design to Vivado 2013.2 (fmcomms1)
Rejeesh, Thanks for the awnser, we will wait for the new release. fvsever
View ArticleRe: Need EDID Register Settings For adv7611(FMC Imageon)
Hi, The question is similar with this one: http://ez.analog.com/thread/21599 Regards,Dragos
View ArticleRe: Need EDID Register Settings For adv7611(FMC Imageon)
Hi Dragos, what would be the front porch,back porch ,sync width for 4kx2k(3840 x 2160) @ 60 fps... Regards,Aneesh
View ArticleRe: PRIM_MODE and VID_STD for UXGA60 (ADV7611, ADV7612, ADV7619)
Hi, 1. I have the same observations. There are a lot of other mistakes in the UG-180 and UG-216 documents also.For example according to CEA-861 Video ID Codes 17,18, 21, 22, 25, 26, 29, 30, 37, 38 are...
View ArticleRe: ADV7623 WUXGA setting
Hi Jeyasudha.M, Thank you very much for your support. Best regards, Nikkee
View ArticleRe: AD2S1210 In 360 Degree Phase Lock Mode
Hi Peter, If you set it to 360 degrees, the D1 bit in the fault register can still be set. The reason behind this is - should the phase lock range is set to 360 degrees, the accuracy of the AD2S1210 is...
View ArticleRe: Halt when starting kernel
1. I'm a little confused now. You say in the first sentence not to mess with the kernel configuration but them you say to disable drivers in the 'make linux-menuconfig'. Isn't that messing with the...
View ArticleADL5513 log detector Temperature data required
Dear Sir, I am using log detector ADL5513ACPZ in my design.I have tested the log detector in following conditions. Operating Freq Range:1.6GHz Voltage applied to TADJ pin : 0.88V...
View ArticleEMC problem with ADSP BF524
Hi I have just finished a product using ADSP BF524 that works nicely except that it fails emission tests with peaks at 480, 720 and 960MHz. Using sniffer probes I am pretty sure this stems from the...
View ArticleRe: PRIM_MODE and VID_STD for UXGA60 (ADV7611, ADV7612, ADV7619)
Hi Peter, Thank you for giving your feedback, It will be provided to the team that looks after the documentation. In general - free run settings are totally up to the user. You may want to enable...
View ArticleRe: SSM2603 and L/R DAC Volume
Just to clarify, I mis-typed, it wasn't LIN or RIN, it was supposed to be LOUT and ROUT.
View ArticleRe: ADV7612 Clocking
In what cases an External Clock Oscillator Source is used and in what cases Crystal ( XTAL ) is used?What is the difference between these 2 methods? Maybe there is some paper describing it?
View ArticleTDM between AD1401 and AD1940 eval boards
Hi, I've been able to send I2S stereo audio from a AD1401 eval board to a AD1940d boar by connecting them as described inhttp://ez.analog.com/thread/35830 Now I'd like to try sending...
View ArticleRe: Method to address 32 or more ADCs on the same SPI bus?
Although I2C has been used to route signals from one card or PCB to another, the original intent was to keep any given I2C bus on one PCB. That said, it is indeed possible to take I2C lines from one...
View ArticleRe: Method to address 32 or more ADCs on the same SPI bus?
Thanks Nick. I will share this option with the customer and let you know if they have any follow on questions.
View Article