Re: BF54x USB host mass storage reconnect..
Hi. Here are our modifications in USB part.Don't be surprised if you will find it tricky. They are tricky. Hope you will find some useful things there. Dmitry P.S. paths in files edited with the...
View ArticleADV 7611 detected fps
Dear All, How can i know the hdmi input frame rate(fps) detected by adv 7611 ?Is there any register which holds the input frame rate value ? Regards,Aneesh
View Article+/-10V driver for AD7190? differential or single-ended mode?
Hi all,I'm designing a temperature measurement system with low bandwidth, 10Hz or less, and high DC-precision requirement.The sensor frontend amplifier outputs a +/-10V signal which I want to digitize...
View Article8Khz Sample Rate BF52xC1 & G711u-law
Hi there, So i've implemented what is essentially a "Multicast Speaker" on the EZ-KIT BF527. It samples G711u-law packets, delivers the payload to the G711 decoder (the demo version from ADI) and the...
View ArticleRe: CCES: Compiled Simulator?
Hi, CrossCore Embedded Studio does not have separate Compiled and Cycle Accurate Simulators as VisualDSP++ did.There are no plans to include a compiled simulator in CCES. Regards,Craig.
View ArticleRe: AD7705 input signals problems
Hi, Gonzalo. Apology for the delayed response. I would say it really depends on your application. If precision is the objective, noise must be lowered to obtain a higher peak-to-peak resolution but...
View ArticleAD7760 Timing
What is the timing of DRDY with respect to MClk? I am using an FPGA and want to use synchronous logic so need to latch DRDY with MClk (= IClk) or do I have to latch DRDY in a set/reset latch because...
View ArticleRe: uC/OS III Manual Simple example
Hi Mike, That manual is a copy of the Micrium documentation, rather than something we have produced ourselves. The PDF is locked - I expect Micrium provide it this way. The examples contained therein...
View ArticleRe: AD8342 - insufficient Input-P1dB ?
Hello Peng, Thank you for the useful insights. As to your points,1. Yes, the input RF port is well-matched for our desired operating frequency range. It was also verified with a network analyzer. The...
View ArticleRe: MISRA and C++
Hi Mike, We only have MISRA-C checking in our compiler at present; we do not have MISRA-C++ checking, unfortunately. Having a quick search, there are static C/C++ analysis plugins available for...
View ArticleRe: Problems of using spice model for simulation AD633.cir (LTspice)
The amendment that I was told it was going to fix it. Everything is working. lacked a little recording.You are very effective. Big thank you!
View ArticleADN4604 IBIS Model
Hello, I am using the ADN4604 Component at my design and I would to receive IBIS model of the component in order to perform Signal Integrity simulation at Hyperlynx. Any other format that Hyperlynx can...
View ArticleRe: How to port VDSP asm L1_data_b?
Hi illishar, sorry for the late response, actually we are not able to cover this, could you get help fromez.analog.com/community/dsp/software-and-development-tools/gnu-toolchain-blackfin
View ArticleRe: Can't make asm samples work
Hi illishar, sorry for the late response, actually we are not able to cover this, I've moved it to the toolchain forum, please go on to discuss here.
View ArticleRe: AD7760 Timing
Hi Dave, We are looking into this. We will get back to you as soon as possible. Thanks and Best Regards,Chris
View ArticleADSP-BF609 HIBERNATE -> FULL ON
HI, In CCES, I called "adi_pwr_SetPowerMode(ADI_PWR_MODE_HIBERNATE);" to make DSP(bf609) hibernate, and call "adi_pwr_EnableWakeupSignal (ADI_PWR_WAKEUP1, ADI_PWR_WAKE_POL_LOW, true);" to...
View ArticleRe: SDI of ADN4604
Hi,I want more information about ADN4604,so I have no choice but to reject the earlier correct answer to reopen this title.That mustn't be a nicely behavior,would you please forgive me for the bad,,I...
View ArticleClik here to view.
Re: Linearity Error AD7767
Hi JohnnyIn the meantime i did some more measurements.First I reduced the MCLK from 1MHz to 500kHz. The linearity error and also the steps are only half.Looks like the change in the input resistance...
View ArticleRe: Can't make asm samples work
Hi,I think that webpage gives slightly confused advice. It seems to be mixing up the intention of assembler directives and pre-processing directives. Instead of using asm directives, just use straight...
View ArticleClik here to view.
ADM3052 with Microchip MCU problem
Hello, Customer used the ADM3052 and Microchip MCU PIC18F66K80 for CAN-BUS isolated function.During loading CAN-BUS function code, customer can't be normal output CAN-BUS signal with ADM3052 and...
View Article