Re: Have a ADIS16364 IMU with the EVAL-ADIS, stalls waiting for transfer from...
Thank you for sharing this insight. We have not had a case like this to try in our lab but we have noticed that the voltage drop from the USB connector to the DUT is higher than we expected so your...
View ArticleADA4961 evaluation board not working
I have the ADA4961 evaluation board EV-ADA4961SDP1Z and it is not working even though the SPI interface software seems to work all right. There is an instruction to load the eeprom file...
View ArticleClik here to view.
Review about circuit GSR sensor using AD5933 and preAmp
I attach files about GSR(Galvanic Skin Response) sensor using AD5933 and pre-amp.One is refer to EVAL Bd and another is refer to DataSheet(small Impedance measure)please, review and comment about that...
View ArticleRe: Problem reading output from AD7961 FMC Board in Zedboard.
Hi, With EN bits set to 0010, the internal reference buffer is disabled, REF pins should be driven with a 4.096 V external reference and REFIN should be connected to 0 V in this mode. REFIN connection...
View ArticleRe: AD7656 IBIS model
Hi, Shay. I have the AD7606 IBIS model which I can send to you but it does not have the same interface as the AD7656. Regards,Karen
View ArticleRe: AD7606 serial input resistors and Capacitors
Hi, Thomas. I'm assuming you're talking about the resistors and capacitors on Figure 34 of the AD7606 datasheet. This merely shows the analog input circuitry which is internal to the ADC. The capacitor...
View ArticleRe: What is the next of obsoleted AD-FMCMOTCON1-EBZ?
Sounds good! rgets,Andrei, pls upload the comparison if you have, I welcome it !Customer also welcome.Thanks Kaos
View ArticleRe: External resisters for AD8330
Hi jstaley, Do you have the reference design circuit for this case?Also what is the recommend OPAMP for external amp. Thanks Kaos
View ArticleRDY not going low on AD7192?
Hi, I am trying to use an AD7192 in continuous conversion mode using 2 bipolar channels, but the RDY pin is not going low. I am interfacing to a MC9S08LH64 micro controller using the SPI mode. I start...
View ArticleADAU1701 Resources Display
The compiler output file for the ADAU144x (and probably others) gives a nice tabulated listing of the resources used by each functional block that has been pulled into the schematic. I can't find this...
View ArticleRe: A -1701 FM MPX Demodulator
Hi, Bob, You linked me to this a week or so ago, at which time I was not aware that you were using the ADAU1701. Could you answer a couple of questions? 1) How fast are you running the 1701?; 2) Do...
View ArticleRe: How to use global variables in user custom algorithms of sigma studio for...
Hi Liang, You may use either of the options (CCES or command prompt) to rebuild a DLM. Best Regards,John
View ArticleClik here to view.
ADL5610,ADL5320 Output Pin Maximum Ratings
Hello.I have a questions,output pin maximum voltage of ADL5610 and ADL5320.In worst case , I can think full swing output voltage and return voltage from Antenna that not matching impedance.Now i thing...
View ArticleADE7816 ANGLEx
Hi, I'm working with ADE7816, to make an energy metering based application. Currently i'm in calibrating the chip, i follow AN-1152 (Calibrating a Single-Phase Energy Meter Based on the ADE7816). From...
View ArticleRe: EV AD9910 Output Filter
Hi Meir, If you are referring to capacitors, C26, C27, C54, C55, 6.8pF has been installed on the evaluation boards.May I know what is your frequency output, clock input and snapshot of your spectrum?...
View ArticleRe: AD8015 as Transimpedance amplifier
Thank you for your reply.I am trying to develop a sensor for which i need I to V conversion for range of -1uA to 1uA with 1nA precession. My sensor pins have given me output current in the range of 1nA...
View ArticleRe: HPUSB-ICE, target requests disconnect ????
Hi,I am facing the same problem.. Did you resolve it ? Can you help me as well
View Articlecan AD9889B support 1080P25 ?
hello, I am using ad9889b as a hdmi transmitter,I use fpga to output 1080p25 video timing and data to ad9889b, some device can receiver the video,but some can not ,i want to know why? does ad9889b...
View ArticleRe: Hi frnds i need ur help.I would implement lms algorithm in audio signal...
Thank you for ur response sir...
View Article