Re: How to transmit my own data with AD9361 in LVDS mode
Wang: Just to confirm - you are doing this on your own custom hardware? -Robin
View ArticleRe: AD9642 - Input Signal Range
Hi Robert, The input span on the AD9642 is differential across the Vin+ and Vin- terminals of the ADC. Each input has a common mode of 0.9V which is set with the Vcm pin. The means each pin will have...
View ArticleClik here to view.
Re: Single supply, PDIP Op-Amps
Dustin, We have a university program, that should save you enough money to afford the Sparkfun adapters: University | Analog Devices Harry
View ArticleAD9393 DVI use
Hi, We would like to use AD9393 in DVI (RGB 444 IN, RGB 444 OUT, no audio). 1)We think that the PLL loop filter in Figure 6 of the datasheet page 10 is not necessary because the audio function is...
View ArticleRe: Change PWM Phase between AH and AL or AH and BH in BF506F
Hello, Apologize for delay in reply on this one. The PWM generator on ADSP-BF506 is capable of operating in two distinct modes, Single - Update Mode and Double - Update Mode. In single-update mode,...
View ArticleRe: ADV7630: How to TMDS PLL reset
HI mattp-san.> but I need to confirm with ADV7630 experts. Do you any update?I need this information!! as soon as possible !Thank you for your support.Best RegardsaimPoint
View ArticleRe: AD8318 overshoot problem
Thank you jdobler and DLVAJOEHere is my circuit schematic that includes an inverting OP-AMP, as jdobler suggested, and CLFP value of 5p6F is used for filtering. I have added a 100R series resistor at...
View ArticleRe: ADE7878 doesn't respond on SPI.
Hello hmani, I am facing similar issue to what uriy had. I am using ADE Evaluation Board along with PIC in a separate breadboard. I opened JP7 (as mentioned in evaluation board manual) and JP2 (as...
View Articlesome questions about ad9361 NO-OS driver run under linux with zynq706
Dear friends, I'm trying to run ad9361 NO-OS driver under linux with zynq706. The kernel version that I'm using is linux-3.14.12, and the platform file is platform_linux. When I read the NO-OS...
View ArticleClik here to view.
Re: Connection failure between VisualDSP and 21020 EZ-ICE
Hi Craig, The Base Adress is correct. (See screenshots) The IceTest doesn't work. How else can I check the connection between software and emulator board? Regards,Christian
View ArticleRe: ADM2582E Noise Margin Expansion
Hi Richard, I have one more question.Does a 1.2kΩ pull-up resister support −9 V to +14 V of the receiver Input Voltage in the absolute maximum ratings? Best regards,Nikkee
View ArticleClik here to view.
How to control current in few uA to few mA?
Hello, I have gotten request for optical VOA test equipment that want to control current Iout from Few uA to mA depend on different VOA because Voltage output of VOA module is tolerance range...
View ArticleRe: AD7147 SPI problem
OK it was indeed very suspicious and at the end I found out that the board was to blame. there was a connection problem to the pins.
View ArticleRe: CCES BF537 Flash Programmer Error
Hi Craig, thank you for your feedback. initialization file is different from flash loader file. I forgat this. Lets say due to be very busy nowadays.I downloaded BSP and re executed to the command with...
View ArticleRe: ADV7513 vsync, hsync, DE and the FLIR Tau2 sensor
First I'd like to point you to the bookVideo Demystified: A Handbook for the Digital Engineer, 5th EditionIt's an excellent resource on anything video and readily available from AmazonCheck out VESA...
View ArticleRe: (ADV7282-M)Can I use Diag-pin when I'm using CVBS(single)?
Yes that should work but I have not verified it on real hardware
View ArticleClik here to view.
Re: Problem of ADAU1401 working at 192kHz sampling rate
Hello, To adjust the ADAU1401 / 1701 sample rate requires two settings -- the one on top of the schematic screen and another setting inside the Hardware Configuration / 170x \ 140x Register...
View ArticleAD6676 driver
Hi, There are FPGA reference designs for the AD6676 evaluation board. However I could not see any software drivers for it. Are there any plans regarding this? If so when is it going to be available...
View ArticleBF537 UART comms
Hi, I m communicating over uart for a number of application. I m using UART1 for dual function and uart0 for signle function. I assigned both interrupt soruce to the same interrupt function IVG-10. My...
View Article