Clik here to view.
Re: How to send RF Modulated Signal using Fiber Optic
Dear Martin, RF modulated signal, even counted it in baud rate, most of them are linear signals in each baud to keep the AM, FM, and PM details. In this way, a laser diode driver for this type of...
View ArticleRe: Question for AD8310
OK, Joel,I got it.Thanks for your help.I will let this know my customer soon. Thanks, Kaos
View ArticleRe: Flashing 21489 EZ Kit Without VDSP++/Emulator
Hi Everyone, I don't have any issues with the earlier comments, but I would like to add a little clarification about some of the various alternatives. An ICE is certainly a tool you want during...
View ArticleClik here to view.
ADSP-21489 IIR cycles
Hello, Below is a table showing SHARC performance from Analog Devices website.When I measured the number of cycles executing Talkthru_IIR_Accelerator example packaged in VDSP5.1, I got more cycles than...
View ArticleRe: Blackfin Hibernate
Many thanks Craig and Joe for your suggestions.Yes, I am maintaining VDDEXT during hibernation. It's only the 3.3 V (powers the SDRAM, FLASH and peripherals) which is switched off during hibernation. I...
View ArticleRe: FMCOMMS 5 with Linux
Chris: Read this page:http://wiki.analog.com/resources/tools-software/linux-software/zynq_images Specifically:Zynq Quick Start Guide [Analog Devices Wiki] and...
View ArticleRe: FMCOMMS 5 with Linux
Ahh, this seems to be the piece of information I was missing! Thanks for the reply, ... I'll try to update the images on my card.
View ArticleRe: ADP5054 Reference Design& ADISimPower
Dear Aaron:I was send email to you. thanks Best Regards, TWN
View ArticleQuestion for AD-FMCCOMMS1-EBZ
Dear Sir/Madam, Your AD-FMCCOMMS1-EBZ can do MIMO and LTE communication.So how did you synchronize between this-PCB and that-PCB?Seems there is not sync-pin on your AD-FMCCOMMS1-EBZ. Thanks Kaos
View ArticleClik here to view.
Re: Problem with AD5764 evaluation board
Hi, Jing. When you changed LK11, what external source did you use and what voltage levels did you use? Regards,Mark
View ArticleRe: iio-osciloscope installation problem
Hello, My GCC version is 4.6.3, which is showed as below:...
View ArticleRe: ADA2200SDP-EVALZ GUI
The latest ACE installer is posted to our Wiki site at http://wiki.analog.com/resources/tools-software/ace. I just want to point out there is a support email at the bottom of the wiki page; also, there...
View ArticleRe: How to icc on bf609?
Hi Aaronwu Following exactly according to: https://blackfin.uclinux.org/doku.php?id=test_mcapi I have reached the stage,I didn't find the following contect: Configure libmcapi in...
View ArticleRe: AMP01 instrumentation amplifier
Hi Vijay, AMP01 gain is 20 Rs/Rg, so at low frequencies the capacitor will look like an open circuit thus giving you a gain of 20. While at high frequencies it will be short circuit and that gives you...
View ArticleRe: Can I drive the AD7626 in a single-ended rather than differential?
Hi Seunghyeon, If I may ask, are you going to build an oscilloscope? If so, it looks like you will be needing more than just an ADC and ADC Driver. Please take a look on this Oscilloscopes and Scope...
View ArticleRe: ADSP-21478 SPI slave boot issues
Hi Chris,i had a similar problem with the ADSP21261. After some trial and error i set the select line for the first 384 bytes, which is the first part of the loader. The program itself is sent with...
View ArticleRe: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
Hi,AcozmaI have put the same command for installing libiio file in ubuntu but it asking password for analog(sudo)what is this .I dont know the passowrd.I simply downloaded image file from the website...
View ArticleRe: ICPLBMissWithoutReplacement error -- while DMA memory transfer
I found the problem causing the error.when i use only one core, no errors occur. and another core being in idle.If both cores enabled and any interrupt generated, after executing interrupt handler,...
View ArticleRe: EVAL-ADAU1761Z to run all ANALOG AUDIO INPUTs?
Hi Coleman,With your help, it works now. Thank a lot! However, the overall output level from mic is not large enough, even though I had boosted the micbias to highest and the mic input stage gain to 6...
View Article