Clik here to view.
Re: Damping Resistor(s) for MCLK Distribution
On a recent prototype board with distributed clocks (of course no fly-wires) --100 ohm damping made the waveforms sloppy, 10 ohms did not prevent the overshoots, but 47 ohms was just right.
View ArticleRe: How to use a Balun at the Output of the Op Amp AD834
Hi, I just want to clarify about your inputs? You say +/-2.5 Amperes? How are you going to connect it to the input?Are you going to put it directly? What is your application?I think answering this will...
View ArticleRe: ADP1048 for 5kW bridgeless PFC
Hi Fan, Definitely the hall ACS 709ACS709 can be ued in this application. James
View ArticleRe: About ADE7953 problem with temperature?
Hi dlath This -0.04 % error about reference meter? You mean the specifications on the ADE7953 INTERFACE AND EVALUATION BOARDS? Regards,Kuanish
View ArticleRe: ADA4870 high output current op amp
Hi, sadegh. Can you please share your schematic so I could simulate it and so we could easily pinpoint the errors? Regards,Anna
View ArticleRe: AD7763 SYNC Signal
Hi Jim_Jim, I am looking into this. I'll get back to you soon. Regards,Jonathan
View ArticleRe: Help to find solution
Hi, We have some reference circuits for pressure and temperature sensors over at Circuits from the Lab. Please check the portfolio for your reference. Hope this helps. Regards,Karen
View ArticleRe: AD9910 Intermittent outputs or just broken
Hi Steve I think the 246.5 MHz frequency corresponds to the SYNC_CLK signal. Try disabling the this signal at the registers and observe if this situation still persists. Best RegardsLouijie
View ArticleQuestions on ADI REFERENCE DESIGNS HDL
Dear all, I am preparing the HDL driver for Vivado. My project is about to develop an application on the platform of Zedboard and FMCOMMS3. I find that 4 kinds of branches are available. What is the...
View ArticleClik here to view.
Regarding AD9361 Calibrations
Hi , We incorporated AD9361 in one of our 2.3-2.4 GHz range Radio card designs. ad9361 is configured to work in FDD, single data rate, dual port mode. As a part of basic testing of the board we used...
View ArticleClik here to view.
Re: ADSP-21479 Software reset
Hi Raymond, Glad to know that the problem is fixed. Thanks for your update. Regards,Jithul
View ArticleRe: ADV7611 IIC
Hi, Thank you very much.I have fixed this problem. Because if i read the adv7611 , firstly I write the salve address and subaddress without P, then I write the salve address. The picture above...
View ArticleRe: LabView source for EVAL-CED1Z + EVAL-AD7621 kit
Hi, We can provide the source code for your reference but we can't support any changes you want to implement. The codes can be downloaded here: Please let me know when you've downloaded the file....
View ArticleRe: ADE7763 readings at low power factor and low current
Hi hmani, Yes you are correct we are using line accumulation mode for energy measurements. Right now we are using 250 half cycles for accumulation. I will increase the number of cycles and check...
View ArticleRe: ADAU1442 with Two ADAU1701
Hello John, Thank-you for your early reply.I did consider the ADAU1451 and the AD1938 CODEC.The ADAU1451 is a new part and the algorithm libraries are not completely available/ported yet. If AD updates...
View ArticleClik here to view.
Sigma 300 (ADAU145x) Slew Volume Rates
Slew volume controls can filter noisy control inputs and minimize clicks. Often the desired slew rate can be found by experiment. However, in some applications it would help to know the actual...
View Articlehow to config Gm mixer sub table?
I have a code for this config. But I don't know the value of gain, bias, control mixer? please help me!
View ArticleAD7150- Issue with data logging
Hi all, I am using AD7150 Evaluation Board, when I log data using "Log Data to File" for a capacitance of 10pF ceramic capacitor the value show in GUI is 10.1766 and the value shown in text file is...
View ArticleQuestions about AD5422
Hi there, I have some questions about AD5422.It would be helpful if somebady helps me with my questions. #1,About Latch pin,I want to update writting datas (control register, DAC data) and want to...
View ArticleClik here to view.
Re: ML605+ADFMCOMMS3
Hi,Adrian, I settled the ERROR:NgdBuild:604 - logical block problems by commenting the followings inaxi_ad9361_dev_if.v: But during the map process,I had an error:ERROR:MapLib:1114 - IDELAYCTRL...
View Article