Clik here to view.
Re: About AD620 Make vs. Buy Error Budget
Hi Tarzan, Unfortunately, the datasheet for the AD620 was written over 20 years ago so we do not have a direct resource to provide you with this information. Most likely, it came from the...
View ArticleRe: AD5560 multiple power rail measurement
Hi, Angela, As attached is our design schematic and we scheme to use AD5560 to source five supplies as DVDD, AVDDH, AVDDN, AVDD_3, AVDD_4 five voltages, these supplies are used to drive the LCD...
View ArticleRe: Some questions about ADV212
Hi Dave,I will try to add some blank pixels between lines. But I still don't understand why the DREQ0 signal becoms low as soon as the firmware loaded successfully, are my parameters set correct?
View ArticleRe: ADV212 RAW and JDATA mode
Hi Dave, Thanks for reply. Maybe I should change the mode to Custom specific or HIPI mode I want to ask one more question. If I follow the programming guide flow chart for raw pixel...
View Articleadp1051 design tool
Hi Sir I want to design the ADP1051 as a power module,can you support the design tool as EXCEL?thanks
View ArticleRe: Single Ended to Differential Converter
Hi, George. Aside from the frequency, what is the input voltage that you will apply to the amplifier? What is your desired output voltage? What is the supply voltage that you will use (single 5V,...
View ArticleRe: adp1051 design tool
Hi Alex, The degign of the isolated power is quite complex. We generally use the MathCAD as design tool. What are the key specifications, such as the power rating, input voltage range, output voltage...
View ArticleRe: AD7626 Application
Hi Jonathan I cann't know whether AD7626 for undersampling, my signal is core frequency of 20MHz, Bandwidth is 5MHz ,so Ihave to use undersampling . Canad7626forundersampling？ yes or no? Regards,...
View ArticleRe: Queries about AD7606 Anti Aliasing Filter
Hi Wayne, For full attenuation, I think it will require external filter. There is link below that will point you to ADI filter wizard that might help you selecting some higher order filter to...
View ArticleRe: ADP5090(quiescent current and sleeping cuurent)
Hi shourya, Thanks for your detailed research on the ADP5090. The quiescent current is not releated to the input voltage and input power, while it depends on the SYS voltage. And also, in cold start,...
View ArticleClik here to view.
Re: Queries about HMC642LC5
hi, there could someone help with my queries or give some comments on it? thanks! Br,Wayne
View ArticleRe: AD7626 Application
Hi Zhouzhx, The AD7626 Tcycle range from 100ns to 10,000ns. This mean that it can have a sample of 100khz to 10Mhz.You may do undersampling. As mentioned, the input structure of the AD7626 does...
View ArticleClik here to view.
DVP Eval Latest Source 10-14-11 Update Boards Issue
Hi all ,I am a new FAE in ADI agent and trying to use EVAL-ADV7280 board following the ADV7280 installation guide Rev A .I have installed the DVP Eval program and put the ADV7280_CUST to the directory...
View ArticleRe: Queries about AD7606 Anti Aliasing Filter
hi, Achim and JonathanMoreover, do you have a transfer function of your digital filter so that we may do some modelling ? Thanks! Br,Wayne
View ArticleRe: AD8182 simulation model
Hi Hoang Dao, The AD8182 does not have a spice model yet. But for simulation purposes, you can use the spice model of AD8170 attached. It has almost same specs and performance with AD8182, the...
View ArticleRe: ADAU7002 SMT Reflow Profile Document
Hi Bill,Many thanks for your quick response and it helps a lot.Jane.
View ArticleLabView source for EVAL-CED1Z + EVAL-AD7621 kit
Hello,We'd like to extend the functionality of the evaluation software (the LabView application called Eval PulSAR-CDF.vi) which is bundled with the evaluation boards to allow us to automate our...
View ArticleRe: AD5560 multiple power rail measurement
Customer also update their question: As attached is our design schematic and we scheme to use AD5560 to source five supplies as DVDD, AVDDH, AVDDN, AVDD_3, AVDD_4 five voltages, these supplies are...
View ArticleRe: How to set up the AD-FMCOMMS1 reference clock
Hi Dragos, We use the method you provide, but the output frequency(J9) still not accurate 10MHz. It's about 10.25MHz, and the Vector Signal Generator(MXG N5182A) can't lock the referance clock. What...
View Article