Clik here to view.
Re: ADE 7953 design consideration
Hi Owais I cannot recommend any particular component manufacturer. But you can browse through the components used in the ADE7953 evaluation board (attached) for reference. Regardshmani
View Articleadsp-bf609-pixc-CCES
Greetings I am having problems understand the PIXC modes of operation, any tutorial or reference please - Work as LCD Driver, OGL, OCV, Blending on video I have blackfin @D Graphics Lib 4.1.0, put...
View ArticleClik here to view.
Re: using AD8067 as inverting amplifier
Hi Niloy, As i read through the datasheet (page 13), I found out the error in your circuit is the value for feedback resistor. 1kohm is recommended as feedback rather than 10kohm.In your case, you can...
View Articlebootng zynq zc702+fmcomms5
Hi , I erased my SD card and loaded the unzipped image in the Zynq quick start page using the win32diskimager application.I then followed the rest of the instructions, including the boot & tools...
View ArticleAD603 Data Sheet Circuit - Figure 49, page 18
Hello: I am making an amateur radio transceiver. I have based the IF strip of the receiver section of the transceiver on the circuit shown in the data sheet page 18 (figure 49). My circuit is as...
View ArticleClik here to view.
Re: Sigma300 (ADAU145x) Q&A
Hello, The Limiter block behaves similarly for me:Its "Flag" output is actually the Ratio output (thus is all over the place)Presumably, then, the "Ratio" output is the Flag -- but it's dead....
View ArticleRe: AD9467
Thanks for a great answer, i think i was confused about the timing diagram on figure 2 on page 7 before, but i makes more sense now. One last question. The 2 output bits on each differential pair, do...
View ArticleRe: Sigma300 (ADAU145x) Q&A
Bob, You are the best. Your test is much appreciated.It's really strange though. Which SigmaStudio version are you using?I'm running 3.11 Build 2, Rev 1396 (9/8/2014) and the limiter does not limit at...
View ArticleRe: ADV212 problem
HI,Are you Chinese? I'm using ADV212 too,and have the same questions you metioned. May be we can help each other
View ArticleRe: Some questions about ADV212
Hi Dave, There is a 8-bit gray-level raw image of 128 pixels X 128 pixels stored in a SRAM. All the pixels are active pixels. MCLK=20MHz,VCLK=20MHz. I use custom sepcific mode to put the image on VDATA...
View ArticleClik here to view.
Re: Sigma300 (ADAU145x) Q&A
Hello, I'm using the same version (3.11, build 2, rev 1386, 9/8/04). The discrepancy between the limiter's -10 dB threshold and the observed 0.5 (-6 dB) reading puzzled me as well. As it...
View ArticleRe: EVAL-AD7173-8SDZ firmware
Hi RobK-san, Thank you for your support.My customer reported me that he confirmed the AD7173-8 operation in his circuit board.Thank you gain for your help. Best Regards,Ricky,
View ArticleRe: BF609 uClinux booting fails
Hi Jeremy, please start a new thread instead of replying on old resolved ones, this would make the issue status tracking easier, thank you.
View ArticleRe: Queries about AD7606 Anti Aliasing Filter
soft reminder...Could someone help with my queries?? thanks! Br,Wayne
View Articleorder free samples
I want to order some free samples from Analog Devices. But when I add samples to sample cart, it didn't work. Please help me. Thank you! The following was prompted to me:We have been unable to validate...
View ArticleRe: The pipeline latency of AD9639?
Hello Jonathan, Thanks a lot. It is very helpful. Best regards,Wei
View ArticleRe: AD603 Data Sheet Circuit - Figure 49, page 18
Hi Allen,Congratulations on taking on quite a challenge, one could write a book on building a high gain IF strip and have plenty of material left over to write sequels. I get a sense of what you're...
View ArticleRe: using AD8067 as inverting amplifier
Hi Niloy, Can you share your schematic of your application so that I can assist you better? What are your input requirements if I may know? As what i understand, you want a gain of -0.826? At to what...
View ArticleRe: using AD8067 as inverting amplifier
Hi Niloy, Can you share your schematic of your application so that I can assist you better? What are your input requirements if I may know? As what i understand, you want a gain of -0.826? At to what...
View ArticleRe: question about blimp to design OSD
hi Jeyasudha: thank you for your kindly response. i have looked thourgh the user guides for blimp and i will try to read all of them clearly. Now in my side, we do not have the emulator...
View Article