Clik here to view.
ADuCM320: How to MDIO evaluation
Hi all. We are planning the development of a system that uses the ADuCM320.So, I want to know the method of verification method of MDIO.Also, Could you tell me the host equipment of recommended MDIO?...
View ArticleRe: Is an impedence matching network required with single ended inputs to...
If you need to optimize input return loss and maximize sensitivity I would recommend matching for both input configurations, single ended and differential inputs.
View ArticleRe: As for your HART DAC AD5410
Hi Kaos, The AD5410 does not have user adjustable gain however the AD5755 products do have user adjustable gain and offset registers. If the AD5410 is required, he will need to use a larger range (0 to...
View ArticleRe: can ADV7181D support four channels cvbs to be converted to BT656...
The ADV7181D can only decode one video stream at a time, therefore it can not do 4 simultaneously. You would require a part with multiple video decoders
View ArticleRe: Excat location of accelerometer(s) in ADIS16448
Hi Mark, thank you so much for the information in that great detail. In contrast to what I expected, we did not have an interface implemented to set IMU registers from the host system, which is...
View ArticleRe: AD9361 FMCOMMS3 Receiver performance at 500 MHz carrier frequency
How was the receiver gain set when you did the measurement? Did you use manual gain control or AGC? I would recommend repeating the experiment using AGC.
View ArticleRe: ADV7181C HS_OUT_SEL Register
Sorry for the delay, I just saw this post. The HS/CS pin should be correct if the HS_OUT_SEL bit is programmed correctly. Make sure some other write in your configuration script is not over writing...
View ArticleClik here to view.
Re: how to observe output spectrum using external PXA Signal Analyzer Agilent...
Hi Charly, Figure below shows verification on our configuration using PXA Signal Analyzer from Agilent N9030A . with 3Mhz spanwith 1kHz span. So based on this experiment I can verify the carrier...
View ArticleRe: ADV7611 EDID configuration
A quick look at this file confirms it has only 2 channel PCM audio at 192, 96, 48 & 32 kHz, 24, 20, 16 bits
View ArticlePart # for T11 Transformer on AD-FMCOMMS1-EBZ REV C
I recently knocked a transformer off of a board rendering it unusable.I’d like to know what the manufacturer and part # for the T11 Transformer on the Analog Devices AD-FMCOMMS1-EBZ REV C is so that I...
View ArticleClik here to view.
Re: ADAS1000 - Technical Questions
Hi Meir: Their new design requirement is to generate a pulse after each pulse of the ECG (with constant delay after the ECG pic) and they are interested to know if is there a signal that can...
View ArticleRecommendations for MEMS gyroscopes PCB design
Hi, Could you please provide a recommendations for MEMS gyroscope (ADXRS450 for example) PCB design like type of material, board thickness, number of layouts, etc.? I would like to have a high reliable...
View ArticleWhat is the AD equivalent part number to discontinued SSM2402...for Audio?
I've been using this SSM2402 for a long time with excellent results but I just discovered it'.s been discontinued since few years.Any suggestion for it?I need ±18 V supply, below 100 ohms Ron, very low...
View ArticleRe: HDCP issues with AppleTV (7612 as the Rx)
Hi Reshmi, I see the issue when I power up the board with the A1469 connected to J8 (RxA). I do not see the issue when I power up the board with the A1469 connected to J9 (RxB). What about you? Do you...
View ArticleRe: What about AD9361 spur performance?
Hi Steve I have moved this question from the Low Power RF Transceiver community to the Wideband RF Transceiver community where you will get support on the AD936x parts. Please continue the discussion...
View ArticleRe: Arbitrary Phase rotation from 0 to 180 degrees?
Hi All, Since this post, a Hilbert Transform block has become available for the ADAU1701. It may be overkill for your application, but this block makes possible a wide-range, wide-frequency...
View ArticleRe: Re: How to use sigmastudio software to realize an external potentiometer...
Hello shaoqin, Please mark this discussion as answered. Thanks, Bob
View ArticleRe: usb to serial connection with Blackfin BF506 and uClinux
Hi Francesco, Is your goal to get Linux running on the BF506? As far as I know, that chip isn't supported by the ADI Linux Project.Aaronwu might be able to give you some more information. Regards, Andre.
View ArticleRe: usb to serial connection with Blackfin BF506 and uClinux
Hello Andrewthank you for answering.I would like to use the linux toolchain to program the BF506, I didn't know it was not supported by the ADI linux project.
View ArticleRe: usb to serial connection with Blackfin BF506 and uClinux
Hi Francesco, My apologies, I mustn't have understood. Is your intention to build bare-metal applications and boot them via U-Boot? If not, can you please provide me with more information of what you...
View Article