Re: CN0235 software
Hi Jamal, I'll need a little more information to properly help you.How many batteries are you monitoring?If you are only monitoring 6 batteries, make sure they are wired to the correct screw terminal...
View ArticleRe: Can ADV7842 support PAL I,B,G,H ?
Yes, check the Standard Definition Processor (SDP) in the hardware manual
View ArticleHSC-ADC-EVALCZ software revision (VisualAnalog)
Hello dear colleagues!Could you clear this question - is it possible work with VisualAnalog actual revision (Rev. 1.9.43.14) in Windows 7, or it's need to use Windows XP?May be, where is a new revision...
View ArticleClik here to view.
Re: BF537 hangs after a cmdline reboot
Hello, I'm back finally.There were no chenges to u-boot. Patch to kernel:diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c index d6e977d..a2df964 100644 ---...
View ArticleRe: Re: AD8302 and AD9834
Hi Joel,I am providing one reference input (inp B) to AD8302 from DDS (AD9834) at 10 MHz frequency and the other through DUT (input A). When I was checking the inputs at AD8302 through CRO, then input...
View ArticleRe: Output offset with AD620
Hi Peter, Thanks for using ADI products on your applications. Where is your input voltage coming from? Can you make sure that it is not floating by ensuring the it is connected to a common ground where...
View ArticleRe: ADL5304 usable range
Hi Peter, I moved your question about the ADL5304 in the RF Community. Someone here should be able to assist you. Best regards,Emman
View ArticleReference input AD5686R
What is refference current,, input range and input Impedance for VRef in if is used as input for externa reference voltage?In addition toconsidering the use ofinternal andexternal referenceconnected...
View ArticleRe: Noise AD9822
I just take the CCD out of the circuit and I still have noise on the digital part, ThanksMajid
View ArticleRe: Re: MAT14 vs. MAT04
Hi AnnaFeB, I have received another question from the customer.His question is difference between two graphs of Base-Emitter-On-Voltage vs. Collector Current,There is big difference of two graphs in...
View ArticleRe: ADV7343 - Input Clock Frequency
Shall i control the output pixel clock out signal on the LLC pin of ADV7611, the DR_STR_CLK[1:0], IO, Address 0x14[3:2] register by Medium low (2×) for LLC up to 60 MHz If using the above register...
View ArticleRe: Standard digital isolator for I2S audio line
Hi MSCantrell, Thank you very much for your reply and concerning. At first for your question, target performance is 5~6 Mbps in current design, however it may increase to around 20 Mbps in near future...
View ArticleClik here to view.
ADV7513 Power Supply Filtering
Hi, The Hardware User Guide of ADV7513 specifies to use an LC filter of 10µH inductor and 10µF capacitor for noise suppresion and also to separate the power domains.In the ADV7511 EVM, we see that...
View ArticleAD7195/CY7C68013 firmware
I am inquiring about obtaining the project source code for the CY7C68013 driving the AD7195 on the Eval board UG-257. The board has a lot of versatility, well designed to get a project up and running...
View ArticleClik here to view.
Re: Run just an .dxe file when in CCES
Needed to follow up at the start of a new term and a new set of students1) Students are unfamiliar with CCES 1.0.3 and I want to run a simple .dxe2) Tell students to build an "empty" project3) Add the...
View ArticleClik here to view.
Re: Run just an .dxe file when in CCES
Found a way -- delete the System directory in the empty project.Right click on executable in Debug directory -- say Debug asBuild occurs -- CCES says nothing to makeCCES loads old executable that was...
View ArticleClik here to view.
ADP230X - Max operating voltage
Hello,keeping in mind the application of the ADP230X, in a non inverting configuration, to obatin -14.5 V from a +5 V power supply, the maximum operating voltage of 20 V is closer near and considering...
View ArticleRe: OP4177 opamp is not working as voltage limiter.
Hello Harry!I selected OP4177 as a replacement for LM148 in my design based on the specs given in datasheet. I found it better in every aspect e.g. offset, bias current, supply current. Slew rate ,...
View Article