Re: When I use IAR "download and debug" ,IAR stoped at "programming flash...
Check that the JLINK / JTAG is set to connect during reset and check the rotary switch is set to 1.
View ArticleClik here to view.
Re: can adv7850 support 4 edid maps for all 4 hdmi ports?
Thanks Dave, for what we wanted, even a hack, the end goal is satisfied. The apple will send unencrypted video so downstream projectors that can't handle encrypted video will display the content. This...
View ArticleRe: AD8370 - Gain adjustment
Hi, I moved this discussion about the AD8370 to the RF components community. Someone here should be able to assist you.Best regards,Emman
View ArticleTrace Unit
For someone coming from using BF5XX processors with VisualDSP++, how do I use the Trace Unit in the BF70X? I understand the Trace Unit is different in the BF70X -- it's based on ARM CoreSight...
View ArticleClik here to view.
AD8348 with added baseband gain
I say you chaps...I've added two LNA (MAX2634 - sorry!) and active filters with gain at baseband. It's a tough one to keep stable!A SPICE model for the AD8348 would have been nice, to check the bias. I...
View ArticleAbout AD5422
Hi there,I have some question about AD5422.Would you give me some advice? #1,According to the datasheet, AD5422 has a Aversion and Bversion.What are the differences between Aversion and Bversion.It...
View ArticleRe: Re: Programming the ADSP-21479 in assembly language
Hi Craig, the linker error I was getting was related to the CRT_HDR definition being commented out but appearing later in the code segment I had posted. Commenting out the segment as well solved the...
View ArticleRe: Re: ADV7625 RXE_HPA pin
The device has an internal resistor. You should not need and external HPA resistor. The 'on-board' phrase in the manual should be 'on-die'
View Articlead9361 SLOWATTACK AGC noos/linux problem at < 8.215 Msps
Hello, I am using an fmcomms3 + zedboard. I am attempting to run the ad9361 at a lower sample rate e.g. < 10 Mhz. Using the sd card shipped with the fmcomms3 (using AD provided fpga + linux drivers...
View ArticleRe: ADF4159 - Example of a staircase waveform
Thank you soooooooooooo much! I make it clear where I was wrong~~finally.Wish you happy everyday my dear friend.Thanks
View ArticleRe: AD6657 digital outputs
Hi Mel, Please refer to Figure 2 and Figure 4 in the data sheet. You'll notice that Ch A data is output on the rising edge of the DCO clock while Ch B is output on the falling edge of the DCO clock....
View ArticleClik here to view.
Re: Questions for AD8362
You can change the slope and output scaling using the circuit in Figure 55 (Rev D datasheet) along with equation 15 on the next page. Decide on the desired slope that you want (200 mV/dB). Then pick a...
View ArticleRe: AD8232 EVB question
Hi KJ,Now I have problems like you, how do you solve the problem?Thank you
View ArticleClik here to view.
Re: ADV7170 progreesive input / interlaced output
Hello Hank, This one seems to have slipped by. ADV7170 is an obsolete product and no support is available. Current encoders would be ADV734X or ADV739X. In any case, none of our encoders will interlace...
View ArticleRe: ADV7343 - Input Clock Frequency
We do not have a PC format encoder. The ADV7343 is intended to output SD, ED and HD only not UXGA, UXGA and other PC formats that require discrete H & V syncs. The ADV7611 is a HDMI to parallel...
View ArticleADG936 input DC offset
I am planning to use the ADG936 switches for application where input DC offset is 0.8V. The input signal frequency will be less than 400MHz and the AC swing on each input (each RF1X, RF2X input) can be...
View ArticleRe: Does ADV7182 have no problem when the SOC drives P[7:0] and LLC pins if...
As long as the ADV7182 is powered up and the pins are tri-stated you should have no problems.
View ArticleRe: ADL5902
The short answer is 50 ohms.That's typical with most detectors.The datasheet (http://www.analog.com/static/imported-files/data_sheets/ADL5902.pdf) states in figure 54 and supported by table 8 that a...
View Article